| Code | What the drive shows | Families |
|---|
| F30001 | Power unit: Overcurrent | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30002 | Power unit: DC link voltage overvoltage | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30003 | Power unit: DC link voltage undervoltage | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30004 | Power unit: Overtemperature heat sink AC inverter | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30005 | Power unit: Overload I2t | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30006 | Power unit: Thyristor Control Board | G130, G150, S120, S150 |
| F30008 | Power unit: Sign-of-life error cyclic data | G130, G150, S120, S150 |
| F30011 | Power unit: Line phase failure in main circuit | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30012 | Power unit: Temperature sensor wire breakage | G120, G120XA, G130, G150, S120, S150 |
| F30013 | Power unit: Temperature sensor heat sink short-circuit | G120, G120XA, G130, G150, S120, S150 |
| F30015 | Power unit: Phase failure motor cable | G115D, G120, G120C, G130, G150, S120, S150 |
| F30017 | Power unit: Hardware current limit has responded too often | G120, G120XA, G130, G150, S120, S150 |
| F30020 | Power unit: Configuration not supported | G130, G150, S120, S150 |
| F30021 | Power unit: Ground fault | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30022 | Power unit: Monitoring U_ce | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30024 | Power unit: Overtemperature thermal model | G120, G120XA, G130, G150, S120, S150 |
| F30025 | Power unit: Chip overtemperature | G120, G120XA, G130, G150, S120, S150 |
| F30027 | Power unit: Precharging DC link time monitoring | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30035 | Power unit: Air intake overtemperature | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30036 | Power unit: Internal overtemperature | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30037 | Power unit: Rectifier overtemperature | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30040 | Power unit: Undervolt 24/48 V | G130, G150, S120, S150 |
| F30043 | Power unit: Overvolt 24/48 V | G130, G150, S120, S150 |
| F30045 | Power unit: Supply undervoltage | G130, G150, S120, S150 |
| F30047 | Cooling unit: Cooling medium flow rate too low | G130, G150, S120, S150 |
| F30050 | Power unit: 24 V supply overvoltage | G130, G150, S120, S150 |
| F30051 | Power unit: Motor holding brake short circuit detected | G120, G120XA, G130, G150, S120, S150 |
| F30052 | EEPROM data error | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30053 | FPGA data faulty | G120C, G130, G150, S120, S150 |
| F30055 | Power unit: Braking chopper overcurrent | G120, G130, G150, S120, S150 |
| F30058 | Power unit: heat sink fan defective | S120, S150 |
| F30059 | Power unit: Internal fan faulty | G120, G120C, G120XA, G130, G150, S120, S150 |
| F30060 | Precharge contactor state monitoring | G130, G150, S120, S150 |
| F30061 | Bridging contactor monitoring | G130, G150, S120, S150 |
| F30067 | Power unit: overtemperature, fault capacitor air discharge | S120, S150 |
| F30068 | Power unit: undertemperature inverter heat sink | G120, G120XA, S120, S150 |
| F30070 | Cycle requested by the power unit module not supported | G130, G150, S120, S150 |
| F30071 | No new actual values received from the power unit | G120, G120XA, G130, G150, S120, S150 |
| F30072 | Setpoints can no longer be transferred to the power unit | G120, G120XA, G130, G150, S120, S150 |
| F30074 | Communication error between the Control Unit and Power Module | G120, G120C, G120XA, G130, G150, S120, S150 |
| F30075 | Configuration of the power unit unsuccessful | G120, G120XA, G130, G150, S120, S150 |
| F30078 | Power unit: defective fan or line reactor has overheated | S120, S150 |
| F30080 | Power unit: Current increasing too quickly | G120, G120XA, G130, G150, S120, S150 |
| F30081 | Power unit: Switching operations too frequent | G120, G120XA, G130, G150, S120, S150 |
| F30087 | Power unit: coolant temperature has exceeded the fault threshold | S120, S150 |
| F30105 | PU: Actual value sensing fault | G120, G120XA, G130, G150, S120, S150 |
| F30314 | Power unit: 24 V power supply overloaded by PM | G130, G150, S120, S150 |
| F30600 | SI P2: STOP A initiated | G120, G130, G150, S120, S150 |
| F30611 | SI P2: Defect in a monitoring channel | G120, G130, G150, S120, S150 |
| F30625 | SI P2: Sign-of-life error in safety data | G120, G130, G150, S120, S150 |
| F30630 | SI P2: Brake control error | G130, G150, S120, S150 |
| F30631 | Brake control: External release active | G130, G150, S120, S150 |
| F30632 | SI P2: shutoff valve control/feedback signal error | S120, S150 |
| F30649 | SI P2: Internal software error | G120, G130, G150, S120, S150 |
| F30650 | SI P2: Acceptance test required | G120, G130, G150, S120, S150 |
| F30651 | SI P2: Synchronization with Control Unit unsuccessful | G120, G130, G150, S120, S150 |
| F30652 | SI P2: Illegal monitoring clock cycle | G130, G150, S120, S150 |
| F30655 | SI P2: Align monitoring functions | G120, G130, G150, S120, S150 |
| F30656 | SI P2: Motor Module parameter error | G120, G130, G150, S120, S150 |
| F30657 | SI P2: PROFIsafe telegram number invalid | G130, G150, S120, S150 |
| F30659 | SI P2: Write request for parameter rejected | G120, G130, G150, S120, S150 |
| F30664 | Error while booting | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30665 | SI P2: System is defective | G120, G130, G150, S120, S150 |
| F30672 | SI P2: Control Unit software incompatible | G130, G150, S120, S150 |
| F30674 | SI Motion P2: Safety function not supported by PROFIsafe telegram | G130, G150, S120, S150 |
| F30680 | SI Motion P2: Checksum error safety monitoring functions | G120, G130, G150, S120, S150 |
| F30681 | SI Motion P1: Incorrect parameter value | G120, G130, G150, S120, S150 |
| F30682 | SI Motion P2: Monitoring function not supported | G120, G130, G150, S120, S150 |
| F30683 | SI Motion P2: SOS/SLS enable missing | G120, G130, G150, S120, S150 |
| F30684 | SI Motion P2: Safely limited position limit values interchanged | G130, G150, S120, S150 |
| F30685 | SI Motion P2: Safely-Limited Speed limit value too high | G130, G150, S120, S150 |
| F30686 | SI Motion: Illegal parameterization cam position | S120, S150 |
| F30688 | SI Motion P2: Actual value synchronization not permissible | G130, G150, S120, S150 |
| F30692 | SI Motion P2: Parameter value not permitted for encoderless | G120, G130, G150, S120, S150 |
| F30773 | SI Motion P2: Test stop failsafe digital output error | G130, G150, S120, S150 |
| F30801 | Power unit DRIVE-CLiQ: Sign-of-life missing | G130, G150, S120, S150 |
| F30802 | Power unit: Time slice overflow | G120, G120XA, G130, G150, S120, S150 |
| F30804 | Power unit: CRC | G120, G130, G150, S120, S150 |
| F30805 | Power unit: EEPROM checksum error | G120, G120XA, G130, G150, S120, S150 |
| F30809 | Power unit: Switching information not valid | G120, G120XA, G130, G150, S120, S150 |
| F30820 | Power unit DRIVE-CLiQ: Telegram error | G130, G150, S120, S150 |
| F30835 | Power unit DRIVE-CLiQ: Cyclic data transfer error | G130, G150, S120, S150 |
| F30836 | Power unit DRIVE-CLiQ: Send error for DRIVE-CLiQ data | G130, G150, S120, S150 |
| F30837 | Power unit DRIVE-CLiQ: Component fault | G130, G150, S120, S150 |
| F30845 | Power unit DRIVE-CLiQ: Cyclic data transfer error | G130, G150, S120, S150 |
| F30850 | Power unit: Internal software error | G115D, G120, G120C, G120XA, G130, G150, S120, S150 |
| F30851 | Power unit DRIVE-CLiQ (CU): Sign-of-life missing | G130, G150, S120, S150 |
| F30860 | Power unit DRIVE-CLiQ (CU): Telegram error | G130, G150, S120, S150 |
| F30875 | Power unit: power supply voltage failed | G130, G150, S120, S150 |
| F30885 | CU DRIVE-CLiQ (CU): Cyclic data transfer error | G130, G150, S120, S150 |
| F30886 | PU DRIVE-CLiQ (CU): Error when sending DRIVE-CLiQ data | G130, G150, S120, S150 |
| F30895 | PU DRIVE-CLiQ (CU): Alternating cyclic data transfer error | G130, G150, S120, S150 |
| F30896 | Power unit DRIVE-CLiQ (CU): Inconsistent component properties | G130, G150, S120, S150 |
| F30899 | Power unit: Unknown fault | G130, G150, S120, S150 |
| F30903 | Power unit: I2C bus error occurred | G120, G120XA, G130, G150, S120, S150 |
| F30907 | Power unit: FPGA configuration unsuccessful | G130, G150, S120, S150 |
| F30950 | Power unit: Internal software error | G120, G120XA, G130, G150, S120, S150 |
