What it means
F35895 is raised when a DRIVE-CLiQ communication error occurs on the link from the Terminal Module (TM) involved to the Control Unit (CU). The manual lists exactly one fault cause for this code: 11 (= 0B hex), a synchronization error during alternating cyclic data transfer. The affected component is the Terminal Module; which module is involved can be read from the message value.
Why it appears
- A DRIVE-CLiQ communication error has occurred between the Terminal Module (TM) involved and the Control Unit.
- The fault cause is 11 (= 0B hex): a synchronization error during alternating cyclic data transfer.
What to check
- Acknowledge the fault immediately.
- Then carry out the one remedial step the manual specifies:
Carry out a POWER ON.
- For the DRIVE-CLiQ data transfer error shutdown threshold the remedy note points to p9915 (DRIVE-CLiQ data transfer error shutdown threshold master); no further checks are described for this fault.
Reading the message value
- The drive codes the message value in r0949 (fault value) / r2124 (alarm value) as 0000yyxx hex.
- yy = component number of the affected Terminal Module, xx = error cause.
- For this fault the error cause is 11 (= 0B hex), the synchronization error during alternating cyclic data transfer.
Parameters the manual names
- r0949 — fault value: read the coded message value (component number and fault cause) here for this fault.
- r2124 — alarm value: the manual's coding note names r0949/r2124 together, so the same coding applies to the alarm value.
- p9915 — DRIVE-CLiQ data transfer error shutdown threshold master (DQ fault master): the remedy for this fault cross-references this parameter.
Acknowledging and restarting
The fault must be acknowledged immediately. The remedy consists of a single step: Carry out a POWER ON.
After the POWER ON the drive can be restarted; no other reset or remedial procedure is described for this fault.
The same on every family
Every manual that describes F35895 gives it the same reaction, acknowledgement and message class.
| Drive family | Reaction | Acknowledge | Message class | Component | Manual |
|---|---|---|---|---|---|
| S120, S150 | OFF1 (OFF2) | IMMEDIATELY | Internal (DRIVE-CLiQ) communication error (12) | Terminal Module (TM) | SINAMICS S120, S150 List Manual · p. 3240 |
| G130, G150 | OFF1 (OFF2) | IMMEDIATELY | Internal (DRIVE-CLiQ) communication error (12) | Terminal Module (TM) | SINAMICS G130, G150 List Manual · p. 1902 |
The drives this code lives on
F35895 is described for G130, G150, S120, S150. These are the converters of those families in our catalogue — price on request.
Questions technicians ask
What does SINAMICS fault F35895 mean?
A DRIVE-CLiQ communication error occurred between the Terminal Module (TM) involved and the Control Unit. The fault cause is 11 (= 0B hex): a synchronization error during alternating cyclic data transfer.
How do I clear fault F35895?
Acknowledge the fault immediately and then carry out a POWER ON. The manual describes no other remedial step for this fault.
Where can I read the message value of F35895 and what does it tell me?
In r0949 (fault value) or r2124 (alarm value), coded as 0000yyxx hex: yy is the component number, xx the error cause. For this fault xx is 11 (= 0B hex).
Which component triggers F35895?
The Terminal Module (TM) whose DRIVE-CLiQ link to the Control Unit is affected. The component number in the message value identifies which module it is.
Codes next to this one
Source
Written from Siemens' own List Manuals and operating instructions; every number, designation and parameter on this page is checked against them before publication.
All SINAMICS codes: fault and alarm codes · the F35xxx group · SINAMICS manuals · Siemens manuals