Манометр з трубкою Бурдона з контактами перемикача
Опис
У будь-якому місці, де тиск процесу потрібно локально індикувати, а водночас необхідно комутувати кола, цей перемикач-манометр (switchGAUGE) знаходить своє застосування.
Контакти перемикача (електричні контакти перемикача) замикають або розмикають електричне коло керування залежно від положення стрілки індикаторного вимірювального приладу. Контакти перемикача регулюються в межах усього діапазону шкали (див. DIN 16085) і встановлюються переважно під циферблатом, хоча частково — і на верхній частині циферблата. Стрілка приладу (стрілка фактичного значення) вільно переміщується в межах усього діапазону шкали незалежно від встановлення.
Встановлювальну стрілку можна відрегулювати за допомогою знімного регулювального ключа у вікні.
Особливості
- Також доступне виконання з заповненням корпусу для високих динамічних навантажень тиском або вібрацій
- Прилади з індуктивними контактами для використання у вибухонебезпечних зонах
- Прилади з контактами для застосувань у PLC
- Доступне виконання з суцільною захисною перегородкою (Solidfront)
- QR-код на шкалі веде до інформації про конкретний прилад
Питання та відповіді
Який діапазон вимірювання має цей манометр?
Доступні діапазони надлишкового тиску від 0 … 0,6 bar до 0 … 25 bar, а також вакуумметричні (наприклад, -1 … 0 bar) та мановакуумметричні (наприклад, -1 … 3 bar) діапазони. Є також діапазони в kPa, MPa, psi, inHg та kg/cm².
Яка точність вимірювання?
Клас точності 1,0 відповідно до EN 837-1.
Які варіанти процесного приєднання доступні?
R ¼, R ½, G ¼ B, G ½ B, ¼ NPT та ½ NPT.
Для яких середовищ підходить прилад?
Для газоподібних і рідких агресивних середовищ, що не є високов'язкими та не кристалізуються. Деталі, що контактують із середовищем, виготовляються з нержавіючої сталі 1.4404 (316L) або Monel 400 (2.4360).
Які допустимі температури?
Температура середовища: -20 … +200 °C; температура навколишнього середовища: -20 … +60 °C.
Чи можна використовувати прилад у вибухонебезпечних зонах?
Так, виконання з індуктивними контактами має сертифікацію ATEX та IECEx: II 2G Ex ia IIC T6/T5/T4 Gb (газ) і II 2D Ex ia IIIB T135°C Db (пил).
Чим PGS23.100 відрізняється від сусідніх моделей серії?
PGS23.100 — це виконання з діаметром циферблата NS 100 (100 мм); серія також пропонує виконання NS 160 (160 мм). Обидва призначені для процесної промисловості та можуть комплектуватися заповненням корпуса для високих динамічних навантажень або вібрацій.
Який ступінь захисту корпусу?
IP65.
Зберіть PGS23.1X0 під свою задачу
Артикул збирається автоматично. Якщо сумніваєтесь — напишіть інженеру; підкажемо за параметрами лінії.
- ModelPGS23
- Nominal size100
- switchмагнітний кінцевий вимикач миттєвої дії, модель 821
- first switch operationmakes (1)
- second switch operationбез
- third switch operationбез
- Explosion protectionбез
- Electrical connectionбокова частина штекера
- Contact designбез
- Unit of outer Scaleбар
- Measuring rangeдіапазон тиску надлишкового манометра
- Scale range—
- 2nd Scale or Special Scaleбез
- Process connectionG 1/2 B
- Connection locationнижнє кріплення
- Liquid Damping (case filling)без заповнення
- Caseз запобіжним диском від розриву під тиском
- Mounting optionбез
- Restrictorбез
- Special design featuresбез
- Certificatesбез
Завершіть конфігурацію
Оберіть всі параметри, щоб надіслати запит.
| Модель | PGS23.100 |
| Сімейство | PGS23 |
| Підтип | Pressure gauge with switch contacts |
| Діапазон тиску | 0…0.6 bar · 0…1 bar · 0…1.6 bar · 0…2.5 bar · 0…4 bar · 0…6 bar · 0…10 bar · 0…16 bar · 0…25 bar · 0…60 kPa · 0…100 kPa · 0…160 kPa · 0…250 kPa · 0…400 kPa · 0…600 kPa · 0…1000 kPa · 0…1600 kPa · 0…2500 kPa · 0…0.06 MPa · 0…0.1 MPa · 0…0.16 MPa · 0…0.25 MPa · 0…0.4 MPa · 0…0.6 MPa · 0…1 MPa · 0…1.6 MPa · 0…2.5 MPa · 0…60 psi · 0…100 psi · 0…160 psi · 0…400 psi · 0…600 psi · -1…0 bar · -1…0.6 bar · -1…1.5 bar · -1…3 bar · 0…200 psi · 0…300 psi · 0…800 psi · -100…0 kPa · -100…60 kPa · -100…150 kPa · -100…300 kPa · -30…0 inHg · -30…15 inHg · -30…30 inHg · -30…60 inHg · 0…10 psi · 0…15 psi · 0…30 psi · -1…9 bar · -1…15 bar · -1…24 bar · -1…30 bar · -100…900 kPa · -100…1500 kPa · -100…2400 kPa · -100…3000 kPa · -0.6…0 bar · 0…1000 psi · 0…1500 psi · 0…2000 psi · 0…3000 psi · 0…4000 psi · 0…5000 psi · 0…6000 psi · 0…7500 psi · 0…10000 psi · 0…15000 psi · 0…20000 psi · 0…0.6 kg/cm² · 0…1 kg/cm² · 0…1.6 kg/cm² · 0…2.5 kg/cm² · 0…4 kg/cm² · 0…6 kg/cm² · 0…10 kg/cm² · 0…16 kg/cm² · 0…25 kg/cm² · -60…0 kPa · -0.06…0 MPa · -0.1…0 MPa · -0.1…0.06 MPa · -0.1…0.15 MPa · -0.1…0.3 MPa · -30…100 inHg · 0…40 kg/cm2 · 0…60 kg/cm2 · 0…100 kg/cm2 · 0…160 kg/cm2 · 0…250 kg/cm2 · 0…400 kg/cm2 · 0…600 kg/cm2 · 0…1000 kg/cm2 · 0…1600 kg/cm2 · 0…40 bar · 0…60 bar · 0…100 bar · 0…160 bar · 0…250 bar · 0…400 bar · 0…600 bar · 0…1000 bar · 0…1600 bar · 0…4000 kPa · 0…6000 kPa · 0…10000 kPa · 0…16000 kPa · 0…25000 kPa · 0…40000 kPa · 0…60000 kPa · 0…100000 kPa · 0…160000 kPa · 0…4 MPa · 0…6 MPa · 0…10 MPa · 0…16 MPa · 0…25 MPa · 0…40 MPa · 0…60 MPa · 0…100 MPa · 0…160 MPa |
| Клас точності | 1.0 |
| Стандарт точності | EN 837-1 |
| Технологічне приєднання | R ¼R ½G ¼ BG ½ B¼ NPT½ NPTG 1/4 BG 1/2 BR 1/4R 1/21/4 NPT1/2 NPT |
| Темп. процесу | −20…+200 °C |
| Вихідний сигнал | Magnetic snap-action contact · Inductive contact · Electronic contact · Reed switch |
| Живлення | DC 10 ... 30 V |
| Електр. приєднання | Cable socket, black Per VDE 0110 insulation group C/250 V Cable gland M20 x 1.5 |
| Функція перемикання | Normally open, Normally closed, Change-over contact |
| Перемикальні контакти | 3 |
| Матеріал корпусу | Stainless steel 1.4301 (304), Stainless steel 1.4571 (316 Ti) |
| Матеріал змочуваних частин | Stainless steel 1.4404 (316L), Monel 400 (2.4360), Stainless steel |
| Матеріал ущільнення | Silicone oil M50 |
| Темп. навколишнього середовища | −20…+60 °C |
| Ступінь захисту IP | IP65 |
| Вага | 1.3 kg |
| Сертифікати | CERoHSUKCAEACREACHNACE MR0175/ISO 15156NACE MR0103/ISO 17945 |
| Вибухозахист | II 2G Ex ia IIC T6/T5/T4 GbII 2D Ex ia IIIB T135°C DbATEXIECExGas II2G Exia IIC T6/T5/T4 GbDust II2D Exia IIIB T135℃ Db |
| Діаметр шкали | 100 mm |
| Мови datasheet | EN, DE |
| Temperature error | On deviation from the reference conditions at the measuring system: ≤ ±0.4 %per 10 °C [≤ ±0.4 %per 18 °F] of full scale value |
|---|---|
| Switch hysteresis | Depending on the type of contact used, see page 8 |
| Reference conditions | |
| Ambient temperature | +20 °C [+68 °F] |
| bar | |
|---|---|
| 0 ... 0.6 | 0 ... 40 |
| 0 ... 1 | 0 ... 60 |
| 0 ... 1.6 | 0 ... 100 |
| 0 ... 2.5 | 0 ... 160 |
| 0 ... 4 | 0 ... 250 |
| 0 ... 6 | 0 ... 400 |
| 0 ... 10 | 0 ... 600 |
| 0 ... 16 | 0 ... 1,000 |
| 0 ... 25 | 0 ... 1,600 |
| kPa | |
|---|---|
| 0 ... 60 | 0 ... 4,000 |
| 0 ... 100 | 0 ... 6,000 |
| 0 ... 160 | 0 ... 10,000 |
| 0 ... 250 | 0 ... 16,000 |
| 0 ... 400 | 0 ... 25,000 |
| 0 ... 600 | 0 ... 40,000 |
| 0 ... 1,000 | 0 ... 60,000 |
| 0 ... 1,600 | 0 ... 100,000 |
| 0 ... 2,500 | 0 ... 160,000 |
| psi | |
|---|---|
| 0 ... 10 | 0 ... 1,000 |
| 0 ... 15 | 0 ... 1,500 |
| 0 ... 30 | 0 ... 2,000 |
| 0 ... 60 | 0 ... 3,000 |
| 0 ... 100 | 0 ... 4,000 |
| 0 ... 160 | 0 ... 5,000 |
| 0 ... 200 | 0 ... 6,000 |
| 0 ... 300 | 0 ... 7,500 |
| 0 ... 400 | 0 ... 10,000 |
| 0 ... 600 | 0 ... 15,000 |
| 0 ... 800 | 0 ... 20,000 |
Переглянути всі (20)
| 0 ... 0.6 | 0 ... 40 |
|---|---|
| 0 ... 1 | 0 ... 60 |
| 0 ... 1.6 | 0 ... 100 |
| 0 ... 2.5 | 0 ... 160 |
| 0 ... 4 | 0 ... 250 |
| 0 ... 6 | 0 ... 400 |
| 0 ... 10 | 0 ... 600 |
| 0 ... 16 | 0 ... 1,000 |
| 0 ... 25 | 0 ... 1,600 |
| 0 ... 0.06 | 0 ... 4 |
|---|---|
| 0 ... 0.1 | 0 ... 6 |
| 0 ... 0.16 | 0 ... 10 |
| 0 ... 0.25 | 0 ... 16 |
| 0 ... 0.4 | 0 ... 25 |
| 0 ... 0.6 | 0 ... 40 |
| 0 ... 1 | 0 ... 60 |
| 0 ... 1.6 | 0 ... 100 |
| 0 ... 2.5 | 0 ... 160 |
| bar | |
|---|---|
| -0.6 ... 0 1) | -1 ...+5 |
| -1 ... 0 | -1 ...+9 |
| -1 ... +0.6 | -1 ...+15 |
| -1 ... +1.5 | -1 ...+24 |
| -1 ...+3 | -1 ...+30 |
| -60 ... 0 1) | -100 ...+500 |
|---|---|
| -100 ... 0 | -100 ...+900 |
| -100 ...+60 | -100 ... +1,500 |
| -100 ...+150 | -100 ... +2,400 |
| -100 ...+300 | -100 ... +3,000 |
| -0.06 ... 0 1) | -0.1 ... +0.5 |
|---|---|
| -0.1 ... 0 | -0.1 ... +0.9 |
| -0.1 ... +0.06 | -0.1 ... +1.5 |
| -0.1 ... +0.15 | -0.1 ... +2.4 |
| -0.1 ... +0.3 | -0.1 ...+3 |
| -30 inHg ... 0 | -30 inHg ...+100 |
|---|---|
| -30 inHg ...+15 | -30 inHg ...+160 |
| -30 inHg ...+30 | -30 inHg ...+200 |
| -30 inHg ...+60 | -30 inHg ...+300 |
| Process connection | ||
|---|---|---|
| Standard | ■ EN 837-1 ■ ISO 7 ■ ANSI/B1.20.1 | |
| Size | ||
| EN 837-1 | ■ G¼B,male thread ■ G½B,male thread | |
| ISO 7 | ■ R ¼, male thread ■ R ½, male thread | |
| ANSI/B1.20.1 | ■ ¼NPT, male thread ■ ½NPT, male thread | |
| Restrictor | ■ Without ■ ∅0.6 mm[0.024"], stainless steel ■ ∅0.3 mm[0.012"], stainless steel ■ ∅0.6 mm[0.024"], Monel | |
| Material (wetted) | ||
| Process connection | Model PGS23 | Stainless steel 1.4404 (316L) |
| Model PGS26 | Monel 400 (2.4360) | |
| Bourdon tube | Model PGS23 | Stainless steel 1.4404 (316L) |
| Model PGS26 | Monel 400 (2.4360) |
| Output signal | |
|---|---|
| Type of contact | ■ Magnetic snap-action contact, model 821, see page 6 ■ Inductive contact, model 831, see page 7 ■ Electronic contact, model 830 E, see page 8 ■ Reed switch, model 851, see page 9 |
| Switching technology | |
| Magnetic snap-action contact, model 821 | ■ No control unit and no supply voltage required ■ Direct switching up to 250 V, 1 A |
| Inductive contact, model 831 | ■ Suitable for use in hazardous areas with corresponding control unit (model 904.xx) ■ Long service life due to non-contact sensor ■ Low influence on the indication accuracy ■ Fail-safe switching at high switching frequency ■ Insensitive to corrosion ■ Also available in safety version |
| Electronic contact, model 830 E | ■ For direct triggering of a programmable logic controller (PLC) ■ Long service life due to non-contact sensor ■ Low influence on the indication accuracy ■ Fail-safe switching at high switching frequency ■ Insensitive to corrosion |
| Reed switch, model 851 | ■ No control unit and no supply voltage required ■ Direct switching up to 250 V, 1 A ■ For direct triggering of a programmable logic controller (PLC) ■ Free from wear as without contact |
| Contact setting | ■ Contact(s) adjustable, adjustment key attached to cable socket ■ Contact(s) fixed, without adjustment lock 1) ■ Adjustment lock sealable (tamper-proof) ■ Adjustment lock sealed (tamper-proof) 1) ■ Captive adjustment key with the adjustment lock connected |
| Type of contact | Magnetic snap-action contact |
|---|---|
| Switching technology | ■ No control unit and no supply voltage required ■ Direct switching up to 250 V, 1 A |
| Number of switch contacts | Max. 3 switch contacts |
| Switching function | ■ Separate circuits with ≥ 2 switches ■ Cable break monitoring with parallel resistance (47 kΩ or 100 kΩ) The switching function of each switch is indicated by index 1, 2 or 3 |
| Model 821.1 | Normally open (clockwise pointer motion) |
| Model 821.2 | Normally closed (clockwise pointer motion) |
| Model 821.3 | Change-over contact; one contact breaks and one contact makes simultaneously when pointer reaches set point |
| Switch point setting | Set pointers of the contact pressure gauges are freely adjustable over the full scale range |
| Setting range (recommended) | 25 ... 75 %of span 1) |
| Distance between switch points | Recommended minimum distance between 2 contacts: 20 %of span |
| Switch hysteresis | 2 ... 5 %(typical) |
| Switching current | 0.02 ... 0.3 A (resistive load) Permissible switch-on and switch-off current: ≤ 0.5 A |
| Switching voltage 2) | AC/DC 24 ...250V |
| Switching power | |
| Unfilled instruments | ≤ 30 W, ≤ 50VA |
| Filled instruments | ≤ 20 W, ≤ 20VA |
| Contact material | Silver-nickel, gold-plated |
| Switching voltage | Unfilled instruments | Filled instruments | ||||
|---|---|---|---|---|---|---|
| Resistive load | Inductive load | Resistive load | Inductive load | |||
| Direct current | Alternating current | cos ϕ>0.7 | Direct current | Alternating current | cos ϕ>0.7 | |
| DC 220 V / AC 230 V | 100mA | 120mA | 65mA | 65mA | 90mA | 40mA |
| DC 110 V / AC 110 V | 200mA | 240mA | 130mA | 130mA | 180mA | 85mA |
| DC 48 V / AC 48 V | 300mA | 450mA | 200mA | 190mA | 330mA | 130mA |
| DC 24 V / AC 24 V | 400mA | 600mA | 250mA | 250mA | 450mA | 150mA |
| Type of contact | Inductive contact |
|---|---|
| Switching technology | ■ Suitable for use in hazardous areas with corresponding control unit (model 904.xx) ■ Long service life due to non-contact sensor ■ Low influence on the indication accuracy ■ Fail-safe switching at high switching frequency ■ Insensitive to corrosion ■ Safety version available |
| Number of switch contacts | Max. 3 switch contacts |
| Switching function | Contact versions: ■ 831-N ■ 831-SN, safety version 1) ■ 831-S1N, safety version 1) , inverted signal |
| The switching function of each switch is indicated by index 1 or 2 | |
| Model 831.1 | Normally open (clockwise pointer motion) |
| Model 831.2 | Normally closed (clockwise pointer motion) |
| Switch point setting | Set pointers of the contact pressure gauges are freely adjustable over the full scale range |
| Setting range (recommended) | 10 ... 90 %of span 2) |
| Distance between switch points | Up to 2 contacts can be set to an identical set point. For a version with 3 contacts this is not possible.The left (no. 1) or right (no. 3) contact may not be set to the same set point as the other 2 contacts.The required displacement is approx. 30°, optionally to the right or to the left. |
| Switching current | Depending on the control unit used, see data sheet AC 08.04 |
| Switching voltage | Depending on the control unit used, see data sheet AC 08.04 |
| Switching power | Depending on the control unit used, see data sheet AC 08.04 |
| Permissible temperature ranges in hazardous areas | |
| T6 | -20 ...+60 °C |
| T5 ...T1 | -20 ...+70 °C |
| T135°C | -20 ...+70 °C |
| Model | Version | Ex version |
|---|---|---|
| 904.28 KFU8-SR-Ex1.W | 1 contact | Yes |
| 904.29 KFU8-SR-Ex2.W | 2 contacts | Yes |
| 904.30 KHA6-SH-Ex1 | 1 contact | Yes - Safety version |
| 904.33 KFD2-SH-Ex1 | 1 contact | Yes - Safety version |
| 904.25 MSR 010-I | 1 contact | No |
| 904.26 MSR 020-I | 2 contacts | No |
| 904.27 MSR 011-I | Two-point control | No |
| Type of contact | Electronic contact (PNP transistor) |
|---|---|
| Switching technology | ■ For direct triggering of a programmable logic controller (PLC) ■ Long service life due to non-contact sensor ■ Low influence on the indication accuracy ■ Fail-safe switching at high switching frequency ■ Insensitive to corrosion |
| Number of switch contacts | Max. 3 switch contacts |
| Switching function | Contact versions: ■ 2-wire system ■ 3-wire system |
| Model 830 E.1 | Normally open (clockwise pointer motion) |
| Model 830 E.2 | Normally closed (clockwise pointer motion) |
| Setting range (recommended) | 10 ... 90 %of span (0 ... 100 %onrequest) |
| Distance between switch points | Up to 2 contacts can be set to an identical set point. For a version with 3 contacts this is not possible.The left (no. 1) or right (no. 3) contact may not be set to the same set point as the other 2 contacts.The required displacement is approx. 30°, optionally to the right or to the left. |
| Switching current | ≤ 100mA |
| Switching voltage | DC 10 ...30V |
| Output signal: reed switch, model 851 | |
|---|---|
| Type of contact 1) | Bistable reed switch |
| Switching technology | ■ No control unit and no supply voltage required ■ Direct switching up to 250 V, 1 A ■ For direct triggering of a programmable logic controller (PLC) ■ Free from wear as without contact |
| Number of switch contacts | |
| NS 100 | Max. 2 switch contacts |
| NS 160 2) | 1 switch contact |
| Switching function | ■ Separate circuits with ≥ 2 switches ■ Cable break monitoring with parallel resistance (47 kΩ or 100 kΩ) |
| The switching function of each switch is indicated by index 1, 2 or 3 | |
| Model 851.1 | Normally open (clockwise pointer motion) |
| Model 851.2 | Normally closed (clockwise pointer motion) |
| Model 851.3 | Change-over contact; one contact breaks and one contact makes simultaneously when pointer reaches set point |
| Switch point setting | Set pointers of the contact pressure gauges are freely adjustable over the full scale range |
| Setting range (recommended) | 10 ... 90 %of span |
| Distance between switch points | When using two contacts, these cannot be set to the same point. Depending on the switching function, a minimum clearance of 15 ... 30° is required. |
| Switch hysteresis | 3 ...5% |
| Switching current | ≤ AC/DC 1 A |
| Switching voltage | ≤ AC/DC 250V |
| Switching power | ≤ 60 W, 60VA |
| Contact material | Rhodium |
| Transport current | AC/DC 2 A |
| Inductive load cosϕ | 1 |
| Contact resistance (static) | 100mΩ |
| Insulation resistance | 10 9 Ω |
| Breakdown voltage | DC 1,000V |
| Switching time incl. contact chatter | 4.5 ms |
| Connection type | ■ Cable socket, black PerVDE 0110 insulation group C/250V Cable gland M20 x 1.5 ■ Connector |
|---|---|
| Wire cross-section | 6 screw terminals + PE for 2.5 mm² |
| Cable diameter | Use cable with a diameter of 7 ... 13 mm[0.276 ... 0.512 in] |
| Pin assignment | Connection details are given on the product label of the instrument. Connection terminals and ground terminals are appropriately marked. |
| Material | PA 6 (polyamide) |
| Medium temperature | |
|---|---|
| Unfilled instruments | -20 ...+200 °C [-4 ...+392 °F] |
| Instruments with silicone oil filling | -20 ...+100 °C [-4 ...+212 °F] |
| Ambient temperature | -20 ...+60 °C [-4 ...+140 °F] |
| Pressure limitation | |
| Steady | Full scale value |
| Fluctuating | 0.9 x full scale value |
| Short time | 1.3 x full scale value |
| Ingress protection per IEC/EN 60529 | ■ IP65 ■ IP66 |
Не знайшли відповіді у документації? Інженер відповість впродовж робочого дня.
Запитати інженера →27 стандартних артикулів сімейства PGS23
Якщо знаєте код — оберіть напряму. Якщо ні — користуйтесь конфігуратором у режимі «01».
