| Вид документа | Технічний документ |
|---|---|
| Виробник | SIEMENS |
| Код документа | Analyze-MyPerformance-OEE |
| Сторінок | 296 |
| Мова документа | англійська |
| Розмір файлу | 8.0 МБ |
Текст документа
Introduction 1
Fundamental safety
instructions 2
Product functions 3
Mcenter
Operating on the server 4
Analyze MyPerformance /OEE Using Mcenter on the
server 5
Working with Analyze
Operating Manual
MyPerformance /OEE 6
Configuring AMP /OEE 7
Analyze MyPerformance
API 8
Mendix integration 9
Appendix A
Valid for control:
SINUMERIK 840D, 840D sl/ 840DE sl,
SINUMERIK 828D, SINUMERIK ONE
Software
Mcenter, version 5.3.0.0
Analyze MyPerformance /OEE, version 1.3.0.0
04/2023
A5E50889350B AE
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance
are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG A5E50889350B AE Copyright © Siemens AG 2021 - 2023.
Digital Industries Ⓟ 04/2023 Subject to change All rights reserved
Postfach 48 48
90026 NÜRNBERG
GERMANY
Table of contents
1 Introduction ........................................................................................................................................... 9
1.1 About SINUMERIK ................................................................................................................ 9
1.2 About Mcenter..................................................................................................................... 9
1.3 About Analyze MyPerformance /OEE .................................................................................... 9
1.4 About this documentation ................................................................................................. 10
1.5 Documentation on the internet .......................................................................................... 11
1.5.1 Documentation overview SINUMERIK ONE ......................................................................... 11
1.5.2 Documentation overview SINUMERIK 840D sl..................................................................... 12
1.5.3 Documentation overview SINUMERIK 828D ........................................................................ 13
1.6 Feedback on the technical documentation ......................................................................... 13
1.7 mySupport documentation ................................................................................................ 13
1.8 Service and Support........................................................................................................... 14
1.9 OpenSSL ............................................................................................................................ 16
1.10 Compliance with the General Data Protection Regulation.................................................... 16
2 Fundamental safety instructions......................................................................................................... 17
2.1 General safety instructions................................................................................................. 17
2.2 Warranty and liability for application examples ................................................................... 17
2.3 Security information .......................................................................................................... 17
3 Product functions................................................................................................................................. 19
4 Operating on the server ...................................................................................................................... 21
4.1 Introduction....................................................................................................................... 21
4.2 Logging in to Mcenter........................................................................................................ 22
4.2.1 Without an external authentication provider....................................................................... 22
4.2.2 With an external authentication provider............................................................................ 25
4.3 Displaying information about the product and the version .................................................. 26
4.4 Switch language ................................................................................................................ 27
4.5 Password change ............................................................................................................... 28
4.6 Filtering............................................................................................................................. 30
4.6.1 List filtering........................................................................................................................ 30
4.6.2 Quick filtering .................................................................................................................... 33
5 Using Mcenter on the server ............................................................................................................... 35
5.1 Administration Overview ................................................................................................... 35
5.2 Managing plant hierarchy .................................................................................................. 35
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 3
Table of contents
5.3 Manage users .................................................................................................................... 38
5.3.1 Overview of the users ........................................................................................................ 38
5.3.2 Users and functions ........................................................................................................... 40
5.3.3 Creating new users ............................................................................................................ 44
5.3.4 Updating the account status .............................................................................................. 46
5.3.5 Deleting user accounts....................................................................................................... 49
5.3.6 Resetting the password ...................................................................................................... 52
5.4 Manage machines.............................................................................................................. 54
5.4.1 Overview of machines ....................................................................................................... 54
5.4.2 Creating a new machine type ............................................................................................. 58
5.4.3 Creating a machine ............................................................................................................ 60
5.4.4 Editing a machine .............................................................................................................. 65
5.4.5 Deleting a machine ............................................................................................................ 68
5.5 Manage applications on machines...................................................................................... 69
5.5.1 Overview of assignments ................................................................................................... 69
5.5.2 Machine overview of applications ...................................................................................... 72
5.5.3 Changing assignments....................................................................................................... 74
5.5.4 Updating assignments ....................................................................................................... 76
5.6 Manage openness clients ................................................................................................... 80
5.6.1 Creating a new openness client .......................................................................................... 82
5.6.2 Editing an openness client ................................................................................................. 85
5.6.3 Changing the secret of an openness client.......................................................................... 85
5.6.4 Deleting openness clients................................................................................................... 86
5.7 Manage adapters (experimental)........................................................................................ 88
5.7.1 Overview of adapters ......................................................................................................... 88
5.7.2 Uploading an adapter......................................................................................................... 90
5.7.3 Deleting an adapter ........................................................................................................... 91
5.8 Platform Open API.............................................................................................................. 92
5.8.1 Prerequisites ...................................................................................................................... 92
5.8.2 Retrieve machine states ..................................................................................................... 92
5.8.3 Order management ........................................................................................................... 95
5.8.3.1 Retrieve machines.............................................................................................................. 95
5.8.3.2 Creating a new work sequence........................................................................................... 97
5.8.4 Virus scan (experimental) ................................................................................................ 100
5.8.4.1 Retrieve scanable files ...................................................................................................... 101
5.8.4.2 Update the state of a file .................................................................................................. 103
5.8.4.3 Get a one time URL for downloading a file ........................................................................ 104
6 Working with Analyze MyPerformance /OEE ..................................................................................... 107
6.1 Performance Monitoring .................................................................................................. 107
6.1.1 Opening the Performance Monitoring .............................................................................. 107
6.1.2 Performance Monitoring - OEE ......................................................................................... 107
6.1.3 Machine details................................................................................................................ 111
6.1.3.1 Controlling the performance of the machines................................................................... 111
6.1.3.2 Manual states .................................................................................................................. 118
6.1.3.3 Defining the custom date ................................................................................................. 122
6.1.3.4 Exporting machine status................................................................................................. 123
6.1.3.5 Displaying machine information....................................................................................... 125
6.1.3.6 Adding tags ..................................................................................................................... 126
Analyze MyPerformance /OEE
4 Operating Manual, 04/2023, A5E50889350B AE
Table of contents
6.1.4 Machine comparison........................................................................................................ 127
6.1.5 Dashboards...................................................................................................................... 130
6.1.5.1 Dashboard overview ........................................................................................................ 130
6.1.5.2 Configuring the Welcome page ........................................................................................ 132
6.1.5.3 Generating charts ............................................................................................................ 135
6.1.5.4 Editing charts .................................................................................................................. 145
6.1.5.5 Creating KPIs ................................................................................................................... 148
6.1.5.6 Editing KPIs...................................................................................................................... 153
6.1.5.7 Filtering charts................................................................................................................. 154
6.1.5.8 Exporting data ................................................................................................................. 157
6.1.5.9 Dashboard settings .......................................................................................................... 158
6.1.5.10 Dashboard templates ....................................................................................................... 162
6.2 Utilization Planning.......................................................................................................... 164
6.2.1 Overview ......................................................................................................................... 164
6.2.2 Applied plan .................................................................................................................... 165
6.2.3 Edit plans......................................................................................................................... 167
6.2.3.1 Creating machine utilization plans.................................................................................... 167
6.2.3.2 Edit status........................................................................................................................ 171
6.2.3.3 Copy daily plan ................................................................................................................ 173
6.2.4 Assign plan ...................................................................................................................... 175
6.2.5 Workday details ............................................................................................................... 177
6.2.6 Factory calendar .............................................................................................................. 179
6.3 Production Quality ........................................................................................................... 183
6.3.1 Opening the Production Quality ....................................................................................... 183
6.3.2 Checking the workpieces.................................................................................................. 184
6.3.3 Finding missing workpieces.............................................................................................. 185
6.3.4 Activating workpiece counters ......................................................................................... 186
6.4 Operator States................................................................................................................ 188
6.4.1 Opening the Operator States............................................................................................ 188
6.4.2 Starting an operator state ................................................................................................ 190
6.4.3 Stopping an operator state ............................................................................................... 192
6.4.4 Example of working with Operator States ......................................................................... 192
6.5 Operator States in HMI ..................................................................................................... 194
6.5.1 Operator States in HMI ..................................................................................................... 194
6.5.2 Opening Operator States in HMI ....................................................................................... 195
6.5.3 Using Operator States in the HMI..................................................................................... 197
6.5.4 Starting an Operator State in HMI..................................................................................... 198
6.5.5 Stopping an Operator State in HMI ................................................................................... 199
6.5.6 Using workpiece functions in HMI .................................................................................... 200
6.5.7 Error message.................................................................................................................. 201
6.6 Connecting Fanuc machines to Analyze MyPeformance /OEE ............................................ 202
6.7 Configure AMP /OEE ........................................................................................................ 202
7 Configuring AMP /OEE ....................................................................................................................... 203
7.1 Overview ......................................................................................................................... 203
7.2 Customizing the KPI calculation........................................................................................ 204
7.2.1 Overview ......................................................................................................................... 204
7.2.2 Customizing KPI parameters............................................................................................. 204
7.2.2.1 Working with KPI parameters ........................................................................................... 204
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 5
Table of contents
7.2.2.2 Creating KPI parameters ................................................................................................... 206
7.2.2.3 Deleting KPI parameters ................................................................................................... 209
7.2.2.4 Resetting KPI parameters.................................................................................................. 210
7.2.3 Customizing KPIs ............................................................................................................. 210
7.2.3.1 Working with KPI parameters ........................................................................................... 210
7.2.3.2 Creating KPIs ................................................................................................................... 211
7.2.3.3 Deleting KPIs.................................................................................................................... 215
7.2.3.4 Resetting KPIs .................................................................................................................. 216
7.2.3.5 Editing the OEE algorithm ................................................................................................ 216
7.3 Opening the Configuration............................................................................................... 219
7.4 Editing the Display ........................................................................................................... 219
7.5 Editing the production level ............................................................................................. 222
7.6 Operator States................................................................................................................ 223
7.6.1 Configuring operator states .............................................................................................. 223
7.6.2 Displaying the configuration history ................................................................................. 229
7.6.3 Displaying the manual/operator state history.................................................................... 230
7.7 Machine tags ................................................................................................................... 232
7.8 Sustainability level ........................................................................................................... 237
7.9 Production logic............................................................................................................... 238
7.9.1 Addresses ........................................................................................................................ 238
7.9.2 Machine state calculation................................................................................................. 242
7.10 Customize utilization states.............................................................................................. 244
8 Analyze MyPerformance API.............................................................................................................. 249
8.1 Token for openness interface (extension interface) ........................................................... 249
8.2 Providing and obtaining data via the ERP/MES systems...................................................... 250
8.2.1 Assigning a shift plan ....................................................................................................... 250
8.2.2 Providing shift results....................................................................................................... 260
8.2.3 Getting shift based OEE ................................................................................................... 265
8.2.4 Getting average OEE/KPI................................................................................................... 269
8.2.5 Getting granular OEE/KPI.................................................................................................. 272
8.2.6 Adding custom state ........................................................................................................ 275
8.2.7 Getting all custom states.................................................................................................. 279
9 Mendix integration ............................................................................................................................ 283
9.1 Overview ......................................................................................................................... 283
9.2 Authentication................................................................................................................. 283
9.2.1 Creating an openness client ............................................................................................. 283
9.2.2 Acquiring an access token ................................................................................................ 283
9.2.3 Using the access token ..................................................................................................... 284
9.3 Using the openness client in Mendix ................................................................................ 284
9.3.1 Storing the openness client .............................................................................................. 284
9.3.2 Getting access token from server...................................................................................... 285
9.3.3 Storing access token......................................................................................................... 285
9.3.4 Getting data from Mcenter server..................................................................................... 285
9.4 Using the provided Mendix authentication module........................................................... 286
Analyze MyPerformance /OEE
6 Operating Manual, 04/2023, A5E50889350B AE
Table of contents
9.4.1 Installing the module ....................................................................................................... 287
9.4.2 Setting up authentication................................................................................................. 289
9.4.3 Accessing Mcenter open API............................................................................................. 291
A Appendix............................................................................................................................................ 293
A.1 List of abbreviations......................................................................................................... 293
A.2 Controller addresses......................................................................................................... 294
Index .................................................................................................................................................. 295
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 7
Table of contents
Analyze MyPerformance /OEE
8 Operating Manual, 04/2023, A5E50889350B AE
Introduction 1
1.1 About SINUMERIK
From simple, standardized CNC machines to premium modular machine designs – the
SINUMERIK CNCs offer the right solution for all machine concepts. Whether for individual parts
or mass production, simple or complex workpieces – SINUMERIK is the highly dynamic
automation solution, integrated for all areas of production. From prototype construction and
tool design to mold making, all the way to large-scale series production.
Visit our website for more information SINUMERIK (https://www.siemens.com/sinumerik).
1.2 About Mcenter
About Mcenter
The open, on-premise shopfloor platform Mcenter ensures full transparency and data
consistency. It provides information about tools, NC programs and machine utilization and
connects the machine tools with your IT landscape.
This is possible due to deep integration of higher-level systems with the CNC.
With Mcenter, you can manage different types of machines. You can also work with a range of
third-party controllers via the Machine agent application.
1.3 About Analyze MyPerformance /OEE
Overview
Analyze MyPerformance /OEE calculates important KPIs for the entire plant (such as Overall
Equipment Effectiveness - OEE) and provides important indicators for measures to increase
efficiency.
Through the automatic recording of machine data and conditions as well as through user
dialog entered data, Analyze MyPerformance /OEE provides all the information required for
production optimization.
Customizable options allow for individual calculation and visualization of KPIs to address
customer’s needs.
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 9
Introduction
1.4 About this documentation
1.4 About this documentation
Target group
The operating manual is aimed at all machine tool users. This publication provides information
required by the user to understand the software.
Scope of validity
This manual is valid for use with the following product versions:
• Mcenter, version 5.3.0.0
• Analyze MyPerformance /OEE, version 1.3.0.0
Benefits
The operating manual allows the target group to get familiar with the software user interface.
Based on the manual, the target group is capable of responding to problems and to take
corrective action.
Standard scope
This documentation only describes the functionality of the standard version. This may differ
from the scope of the functionality of the system that is actually supplied. Please refer to the
ordering documentation only for the functionality of the supplied drive system.
It may be possible to execute other functions in the system which are not described in this
documentation. This does not, however, represent an obligation to supply such functions
with a new control or when servicing.
For reasons of clarity, this documentation cannot include all of the detailed information
on all product types. Further, this documentation cannot take into consideration every
conceivable type of installation, operation and service/maintenance.
The machine manufacturer must document any additions or modifications they make to the
product themselves.
Websites of third-party companies
This document may contain hyperlinks to third-party websites. Siemens is not responsible for
and shall not be liable for these websites and their content. Siemens has no control over the
information which appears on these websites and is not responsible for the content and
information provided there. The user bears the risk for their use.
Analyze MyPerformance /OEE
10 Operating Manual, 04/2023, A5E50889350B AE
Introduction
1.5 Documentation on the internet
1.5 Documentation on the internet
1.5.1 Documentation overview SINUMERIK ONE
Comprehensive documentation about the functions provided in SINUMERIK ONE Version 6.13
and higher is provided in the Documentation overview SINUMERIK ONE (https://
support.industry.siemens.com/cs/ww/en/view/109768483).
You can display documents or download them in PDF and HTML5 format.
The documentation is divided into the following categories:
• User: Operating
• User: Programming
• Manufacturer/Service: Functions
• Manufacturer/Service: Hardware
• Manufacturer/Service: Configuration/Setup
• Manufacturer/Service: Safety Integrated
• Information and training
• Manufacturer/Service: SINAMICS
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 11
Introduction
1.5 Documentation on the internet
1.5.2 Documentation overview SINUMERIK 840D sl
Comprehensive documentation about the functions provided in SINUMERIK 840D sl Version 4.8
SP4 and higher is provided in the Documentation overview SINUMERIK 840D sl (https://
support.industry.siemens.com/cs/ww/en/view/109766213).
You can display the documents or download them in PDF and HTML5 format.
The documentation is divided into the following categories:
• User: Operating
• User: Programming
• Manufacturer/Service: Functions
• Manufacturer/Service: Hardware
• Manufacturer/Service: Configuration/Setup
• Manufacturer/Service: Safety Integrated
• Manufacturer/Service: SINUMERIK Integrate/MindApp
• Information and training
• Manufacturer/Service: SINAMICS
Analyze MyPerformance /OEE
12 Operating Manual, 04/2023, A5E50889350B AE
Introduction
1.7 mySupport documentation
1.5.3 Documentation overview SINUMERIK 828D
Comprehensive documentation about the functions provided in SINUMERIK 828D Version 4.8
SP4 and higher is provided in the 828D documentation overview (https://
support.industry.siemens.com/cs/ww/en/view/109766724).
You can display documents or download them in PDF and HTML5 format.
The documentation is divided into the following categories:
• User: Operating
• User: Programming
• Manufacturer/Service: Configuring
• Manufacturer/Service: Commissioning
• Manufacturer/Service: Functions
• Manufacturer/Service: Safety Integrated
• SINUMERIK Integrate/MindApp
• Info & Training
1.6 Feedback on the technical documentation
If you have any questions, suggestions or corrections regarding the technical documentation
which is published in the Siemens Industry Online Support, use the link "Provide feedback"
which appears at the end of the entry.
1.7 mySupport documentation
With the "mySupport documentation" web-based system you can compile your own individual
documentation based on Siemens content, and adapt it for your own machine documentation.
To start the application, click on the "My Documentation" tile on the mySupport homepage
(https://support.industry.siemens.com/cs/ww/en/my):
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 13
Introduction
1.8 Service and Support
The configured manual can be exported in RTF, PDF or XML format.
Note
Siemens content that supports the mySupport documentation application can be identified by
the presence of the "Configure" link.
1.8 Service and Support
Product support
You can find more information about products on the internet:
Product support (https://support.industry.siemens.com/cs/ww/en/)
The following is provided at this address:
• Up-to-date product information (product announcements)
• FAQs
• Manuals
• Downloads
• Newsletters with the latest information about your products
• Global forum for information and best practice sharing between users and specialists
• Local contact persons via our Contacts at Siemens database (→ "Contact")
• Information about field services, repairs, spare parts, and much more (→ "Field Service")
Analyze MyPerformance /OEE
14 Operating Manual, 04/2023, A5E50889350B AE
Introduction
1.8 Service and Support
Technical support
Country-specific telephone numbers for technical support are provided on the internet at
address (https://support.industry.siemens.com/cs/ww/en/sc/4868) in the "Contact" area.
If you have any technical questions, please use the online form in the "Support Request" area.
Training
You can find information on SITRAIN at the following address (https://www.siemens.com/
sitrain).
SITRAIN offers training courses for automation and drives products, systems and solutions from
Siemens.
Siemens support on the go
With the award-winning "Siemens Industry Online Support" app, you can access more than
300,000 documents for Siemens Industry products – any time and from anywhere. The app
can support you in areas including:
• Resolving problems when implementing a project
• Troubleshooting when faults develop
• Expanding a system or planning a new system
Furthermore, you have access to the Technical Forum and other articles from our experts:
• FAQs
• Application examples
• Manuals
• Certificates
• Product announcements and much more
The "Siemens Industry Online Support" app is available for Apple iOS and Android.
Data matrix code on the nameplate
The data matrix code on the nameplate contains the specific device data. This code can be read
with a smartphone and technical information about the device displayed via the "Industry
Online Support" mobile app.
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 15
Introduction
1.10 Compliance with the General Data Protection Regulation
1.9 OpenSSL
Using OpenSSL
This product can contain the following software:
• Software developed by the OpenSSL project for use in the OpenSSL toolkit
• Cryptographic software created by Eric Young.
• Software developed by Eric Young
You can find more information on the internet:
• OpenSSL (https://www.openssl.org)
• Cryptsoft (https://www.cryptsoft.com)
1.10 Compliance with the General Data Protection Regulation
Siemens observes standard data protection principles, in particular the data minimization rules
(privacy by design).
For this product, this means:
The product does not process or store any personal data, only technical function data (e.g.
time stamps). If the user links this data with other data (e.g. shift plans) or if he/she stores
person-related data on the same data medium (e.g. hard disk), thus personalizing this data,
he/she must ensure compliance with the applicable data protection stipulations.
Analyze MyPerformance /OEE
16 Operating Manual, 04/2023, A5E50889350B AE
Fundamental safety instructions 2
2.1 General safety instructions
WARNING
Danger to life if the safety instructions and residual risks are not observed
If the safety instructions and residual risks in the associated hardware documentation are not
observed, accidents involving severe injuries or death can occur.
• Observe the safety instructions given in the hardware documentation.
• Consider the residual risks for the risk evaluation.
WARNING
Malfunctions of the machine as a result of incorrect or changed parameter settings
As a result of incorrect or changed parameterization, machines can malfunction, which in turn
can lead to injuries or death.
• Protect the parameterization against unauthorized access.
• Handle possible malfunctions by taking suitable measures, e.g. emergency stop or
emergency off.
2.2 Warranty and liability for application examples
Application examples are not binding and do not claim to be complete regarding configuration,
equipment or any eventuality which may arise. Application examples do not represent specific
customer solutions, but are only intended to provide support for typical tasks.
As the user you yourself are responsible for ensuring that the products described are
operated correctly. Application examples do not relieve you of your responsibility for safe
handling when using, installing, operating and maintaining the equipment.
2.3 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 17
Fundamental safety instructions
2.3 Security information
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit
https://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customer’s exposure
to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
https://www.siemens.com/cert.
Further information is provided on the Internet:
Industrial Security Configuration Manual (https://support.industry.siemens.com/cs/ww/en/
view/108862708)
WARNING
Unsafe operating states resulting from software manipulation
Software manipulations, e.g. viruses, Trojans, or worms, can cause unsafe operating states in
your system that may lead to death, serious injury, and property damage.
• Keep the software up to date.
• Incorporate the automation and drive components into a holistic, state-of-the-art industrial
security concept for the installation or machine.
• Make sure that you include all installed products into the holistic industrial security concept.
• Protect files stored on exchangeable storage media from malicious software by with suitable
protection measures, e.g. virus scanners.
• On completion of commissioning, check all security-related settings.
Analyze MyPerformance /OEE
18 Operating Manual, 04/2023, A5E50889350B AE
Product functions 3
Functions
Use Analyze MyPerformance /OEE to adjust the representation and visualization of all machine
tools connected to Mcenter:
• Performance Monitoring
With "Performance Monitoring", you have the option to check the performance of the
machines using the performance monitoring function.
Further information can be found in the Chapter: Performance Monitoring (Page 107)
• Utilization Planning
With "Utilization Planning", you have the option of defining the utilization plans for the
individual control system.
Further information can be found in the Chapter: Utilization Planning (Page 164)
• Production Quality
With "Production Quality", you have the option to check the quality of your production.
Further information can be found in the Chapter: Production Quality (Page 183)
• Configure AMP /OEE
With "Configure AMP /OEE", you have the option to configure OEE Machines.
Further information can be found in the Chapter: Configure AMP /OEE (Page 202)
• Operator States
With "Operator States", you have the option to apply operator states created by the system
administrator/supervisor to a machine.
Further information can be found in the Chapter: Operator States (Page 188)
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 19
Product functions
Analyze MyPerformance /OEE
20 Operating Manual, 04/2023, A5E50889350B AE
Operating on the server 4
4.1 Introduction
To access Mcenter, call the corresponding URL in a web browser.
Overview
The start page is called after logging on.
Displaying information about the product and the version (Page 26)
You can start the following applications:
• Analyze MyPerformance /OEE
– Performance Monitoring (Page 107)
– Utilization Planning (Page 164)
– Production Quality (Page 183)
– Configure AMP /OEE (Page 202)
– Operator States (Page 188)
• Mcenter
– Administration Overview (Page 35)
– Manage machines (Page 54)
– Manage applications on machines (Page 69)
– Manage users (Page 38)
– Manage openness clients (Page 80)
– Manage adapters (experimental) (Page 88)
Calling applications with HTTP communication
This Operating Manual only describes calling applications with HTTPS communication.
You can also call all applications with HTTP communication. To do this, use "http" instead of
"https" and add port ":8080" after the IP address.
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 21
Operating on the server
4.2 Logging in to Mcenter
4.2 Logging in to Mcenter
4.2.1 Without an external authentication provider
Prerequisite
You have set up your user account.
Analyze MyPerformance /OEE
22 Operating Manual, 04/2023, A5E50889350B AE
Operating on the server
4.2 Logging in to Mcenter
Procedure
1. Open the following URL: Start page (https://{ServerIP}/start-page)
The login window opens.
– Enter your user credentials.
– Click on the "Login" button.
Note
Invalid login attempt
The error message "Invalid login attempt" is displayed when you enter incorrect credentials.
After the fifth unsuccessful attempt, your user account is locked for 5 minutes.
2. The start page opens.
To use the functions, click on the required application. If you do not see the required
application, the user does not have the necessary role to view it.
E.g. you need administrator rights to use certain Mcenter functions, for example
"Administrate Mcenter".
Analyze MyPerformance /OEE
Operating Manual, 04/2023, A5E50889350B AE 23
Operating on the server
4.2 Logging in to Mcenter
Logging out
1. To log out from the application, open the drop-down menu in the upper right section of the
window.
2. Click "Logout" to log out from all applications.
Analyze MyPerformance /OEE
24 Operating Manual, 04/2023, A5E50889350B AE
Operating on the server
4.2 Logging in to Mcenter
4.2.2 With an external authentication provider
Prerequisite
The user account for the external user has been set up.
Note
Login as an external user
You must configure an external authentication provider to log in as an external user.
Additional information is provided in the Installation Manual "McenПоказано початок документа. Повний текст — у PDF за посиланням вище.
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.