VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation Instructions

Вид документа	Інструкція з монтажу
Виробник	JCI
Код документа	va9208-agx-x-series-on-off-and-floating-point-electric-spring-return-valve
Група обладнання	M9000-342 Weather Shield
Сторінок	14
Мова документа	англійська
Розмір файлу	0.7 МБ

Текст документа

1413795F
VA9208-AGx-x Series On/Off and Floating Point Electric
Spring Return Valve Actuators
Part No. 14-1379-5, Rev. F
Installation Instructions Issued March 2022
VA9208-AGA-3, VA9208-AGC-3
VA9208-AGC-2, VA9208-AGC-2

Applications
The VA9208-AGx-x Series On/Off and Floating Point
IMPORTANT: Use this VA9208-AGx-x Series
Electric Spring Return Actuators are direct-mount valve
On/Off and Floating Point Electric Spring Return
actuators that operate on AC/DC 24 V power. These
Actuator only to control equipment under normal
bidirectional actuators are used to provide accurate
operating conditions. Where failure or malfunction of
positioning on Johnson Controls® VG1000 Series
the electric actuator could lead to personal injury or
1-1/4, 1-1/2, and 2 in. (DN32, DN40, and DN50) ball
property damage to the controlled equipment or
valves in Heating, Ventilating, and Air Conditioning
other property, additional precautions must be
(HVAC) applications.
designed into the control system. Incorporate and
Integral line voltage auxiliary switches, available only maintain other devices, such as supervisory or
on the VA9208-xxC-3 models, indicate end-stop alarm systems or safety or limit controls, intended to
position, or perform switching functions within the warn of or protect against failure or malfunction of
selected rotation range. the electric actuator.
VA9208-AGA-2 actuators include plenum-rated cables IMPORTANT : Utiliser ce VA9208-AGx-x Series
and are specially configured for installation in spaces On/Off and Floating Point Electric Spring Return
used for environmental air-handling purposes other Actuator uniquement pour commander des
than ducts and plenums as specified in National Fire équipements dans des conditions normales de
Protection Association (NFPA) 70: National Electrical fonctionnement. Lorsqu'une défaillance ou un
Code section 300.22(C), Other Space Used for dysfonctionnement du electric actuator risque de
Environmental Air. The space over a hung ceiling used provoquer des blessures ou d'endommager
for environmental air handling purposes is an example l'équipement contrôlé ou un autre équipement, la
of the type of space for which these actuators are conception du système de contrôle doit intégrer des
configured. dispositifs de protection supplémentaires. Veiller
dans ce cas à intégrer de façon permanente
d'autres dispositifs, tels que des systèmes de
supervision ou d'alarme, ou des dispositifs de
sécurité ou de limitation, ayant une fonction
d'avertissement ou de protection en cas de
défaillance ou de dysfonctionnement du electric
actuator.

Installation
Install the ball valve with the actuator at or above the
center line of the horizontal piping (see Figure 1).

IMPORTANT: In steam applications, install the
valve with the stem horizontal to the piping. Failure
to follow this precaution may shorten the life of the
actuator.

VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators 1
Installation Instructions
IMPORTANT: Do not install or use this VA9208
Series Electric Spring Return Valve Actuator in or
near environments where corrosive substances or
vapors could be present. Exposure of the actuator to
corrosive environments may damage the device’s
internal components, and will void the warranty.

Special tools needed
• Digital voltmeter
• T-20 TORX® driver
Dimensions
Valve actuator

FIG:mntpos_H2O_app
See Figure 2 and Table 1 for valve actuator
dimensions.

Figure 1: Mounting positions for chilled
water and condensing atmosphere

IMPORTANT: Before specifying VA9208 Series
Electric Spring Return Valve Actuators for plenum
applications, verify acceptance of exposed plastic
materials in plenum areas with the local building
authority. Building codes for plenum requirements
vary by location. Some local building authorities
accept compliance to UL 1995, Heating and Cooling
Equipment, while others use different acceptance
criteria.

2 VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation
Instructions
3-1/2 (89)
3-29/32 2-7/8 Clearance Required
(99) (73)

Port Marking
Locations

FIG:VA9208X_dims

Figure 2: Spring return VA9208 actuated VG1241, VG1245, VG1841, and VG1845 Series Ball Valve
dimensions, in. (mm)

Table 1: VA9208 actuated VG1241, VG1245, VG1841, and VG1845 Series Ball Valve dimensions, in. (mm)
Valve Valve A B C D E F G
size in. style1
(DN)
1-1/4 All 5-5/32 (131) 1-1/32 (26) 1-23/32 (44) 7-1/4 (184) 3-15/16 (100) 11/32 (9) 1-31/32
(DN32) (50)
1-1/2 All 5-5/16 (135) 1-9/64 (29) 1-57/64 (48) 7-7/16 (189) 4-21/64 (110) 11/32 (9) 2-11/64
(DN40) (55)
2 2-way 5-17/32 (140) 1-15/32 (37) 2-1/8 (54) 7-11/16 (195) 4-27/320 (132) 11/32 (9) 2-27/64
(DN50) (62)
3-way 7-7/8 (200)

1. Port A must always be connected to the coil (Figure 2).

VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation 3
Instructions
Valve actuator with thermal barrier
See Figure 3 and Table 2 for valve actuator dimensions
with optional M9000-561 Thermal Barrier installed.

3-1/2 (89)
3-29/32 Clearance Required
(99)

A
F

Port Marking
Locations
C C

E G B
D

Figure 3: Spring return VA9208 actuated VG1241, VG1245, VG1841, and VG1845 Series Ball Valve
with optional M9000-561 Thermal Barrier installed dimensions, in. (mm)
Table 2: VA9208 actuated VG1241, VG1245, VG1841, and VG1845 Series Ball Valve with optional thermal
barrier installed dimensions, in. (mm)
Valve Valve A B C D E F G
size style1
in.
(DN)
1-1/4 All 9-17/64 (235) 1-1/32 (26) 1-23/32 (44) 7-1/4 (184) 3-15/16 (100) 11/32 (9) 1-31/32 (50)
(DN32)
1-1/2 All 9-15/16 (240) 1-9/64 (29) 1-57/64 (48) 7-7/16 (189) 4-21/64 (110) 11/32 (9) 2-11/64 (55)
(DN40)
2 2-way 9-31/32 (244) 1-15/32 (37) 2-1/8 (54) 7-11/16 (195) 4-27/32 (123) 11/32 (9) N/A
(DN50)
3-way 7-7/8 (200) 11/32 (9) 2-27/64 (62)

1. Port A must always be connected the coil (Figure 3).

4 VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation
Instructions
Accessories
Table 3: Accessories (order separately)
Code number Description
M9000-560 Ball valve linkage kit for applying M9203 and M9208 Series Actuators to VG1000 Series Valves (quantity
1)
M9000-561 Thermal barrier extends M(VA)9104, M(VA)9203, and M(VA)9208 Series Electric Spring Return Actuator
applications to include low pressure steam (quantity 1)
M9000-342 Weathershield kit for VG1000 Series Ball Valve application of M(VA)9104, M(VA)9203, and M(VA)9208
Series Electric Spring Return Actuators (quantity 1)
M9220-604 Replacement manual override cranks with long crank radius: 2.83 in. (72 mm) (quantity 5)
M9208-605 Replacement manual override cranks with short crank radius: 1.83 in. (46.5 mm) (quantity 5)

Mounting 3. Remove the linkage from Side A (Figure 5).
Mounting the actuator to spring return Port A
(coil) open
To mount the actuator to spring return Port A (coil)
open:
1. Turn the valve stem to the position outlined in
Figure 4.

FIG:RMV_LNK

FIG:VG1000

2 Way 3 Way

Figure 4: Positioning the valve stem
2. Mount optional M9000-561 Thermal Barrier to the
valve if fluid temperature exceeds 212°F (100°C).
See the Mounting the thermal barrier section for
more information.
Figure 5: Removing the linkage
Note: Proceed to Step 7 if the ball valve linkage is on
actuator Side B.

VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation 5
Instructions
4. Insert the drive shaft into Side B (Figure 6). 6. Insert fixed pointer and M4x0.7x83 mm long screw
into the Side A actuator hub. Direct the arrow on
the pointer to 100%.

FIG: DRV_SHFT_B

FIG:FXPT_A
Figure 6: Inserting the drive shaft

5. Install linkage base on Side B using the two
#10-14 x 2.75 in. long screws (Figure 7). The
recommended torque is 20 to 24 lb·in.
(2.3 to 2.7 N·m). Figure 8: Installing the fixed pointer

7. Install the actuator on the ball valve (Figure 9).
Tighten the actuator mounting screw to a torque of
10 to 12 lb·in. (1.1 to 1.4 N·m) and snap in the
large adjustable pointer into place.

Figure 7: Installing the linkage

FIG: MNT_ACTA

Figure 9: Mount the actuator

6 VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation
Instructions
Mounting the actuator to spring return Port A 4. Insert the drive shaft into Side A (Figure 12).
(Coil) Closed
To mount the actuator to spring return port A (coil)
closed:
1. Turn the valve stem to the position outlined in
Figure 10.

FIG:VG1000sdB
2 Way 3 Way

Figure 10: Positioning the valve stem Figure 12: Inserting the drive shaft

2. Mount optional M9000-561 Thermal Barrier to the 5. Install linkage base on Side A using the two
valve if fluid temperature exceeds 212°F (100°C). #10 14 x 2.75 in. long screws. The recommended
See the Mounting the thermal barrier section for torque is 20 to 24 lb·in. (2.3 to 2.7 N·m).
more information.
Note: Proceed to Step 7 if the ball valve linkage is on
actuator Side A.
3. Remove the linkage from Side B (Figure 11).

FIG:lnkgA

Figure 13: Installing the linkage

Figure 11: Removing the linkage

VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation 7
Instructions
6. Insert fixed pointer and M4x0.7x83 mm long screw Mounting the thermal barrier
into the Side B actuator hub. Direct the arrow on Figure 16 shows the optional M9000-561 Thermal
the pointer to 0% (Figure 14). Barrier.
Machine Screws

Flange
Nuts
Barrier

Drive
Shaft

Figure 16: Optional M9000-561 Thermal Barrier

To mount the optional thermal barrier:
1. Install the thermal barrier drive shaft into the
thermal barrier by aligning the tab on the drive
shaft with the slot on the thermal barrier
(Figure 17).
Figure 14: Installing the fixed pointer

7. Install the actuator on the ball valve (Figure 15).
Tighten the actuator mounting screw to a torque of
10 to 12 lb·in. (1.1 to 1.4 N·m) and snap the large
adjustable pointer into place.

Figure 17: Installing the drive
shaft into the thermal barrier

2. Rotate the drive shaft to align marks on the top of
the thermal drive shaft with matching marks on the
valve stem.

Figure 15: Mount the actuator

8 VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation
Instructions
3. Mount the thermal barrier onto the valve using the 4. The actuator requires 8-1/2 manual override crank
four included M5x16 mm machine screws and four rotations from the full spring return position to fully
M5 flange nuts. Tighten the screws to a reposition the actuator hub. At the end of travel, the
recommended torque of 21 to 25 lb·in. rotation resistance increases. Do not force the
(2.4 to 2.8 N·m) (Figure 18) manual crank past this point.
5. While holding the manual crank in the wound
position, rotate and hold the red lock shaft
approximately 10° then release the manual crank
to lock the actuator hub in place.
Note: Insert and slightly rotate the manual crank
in the direction indicated by the arrow on the label
to unlock the actuator hub. Alternately, the actuator
hub automatically unlocks when power is applied
to the actuator, and returns the actuator to normal
drive and spring return operation.
Wiring
WARNING: Risk of Electric Shock.

! Disconnect or isolate all power supplies
before making electrical connections.
FIG:in_act More than one disconnection or isolation
may be required to completely
de-energize equipment. Contact with
components carrying hazardous voltage
can cause electric shock and may result
Figure 18: Installing the Barrier in severe personal injury or death.

4. Proceed to the actuator mounting instructions. AVERTISSEMENT : Risque de
Follow the same steps as mounting directly to the décharge électrique.
valve when mounting actuator to the thermal Débrancher ou isoler toute alimentation
barrier. avant de réaliser un raccordement
électrique. Plusieurs isolations et
Note: Depending on your application, you may débranchements sont peut-être
position the assembly in any of the four 90° increments nécessaires pour -couper entièrement
on the valve. l'alimentation de l'équipement. Tout
Manual override contact avec des composants porteurs
de tensions dangereuses risque
Use only the supplied manual override crank to
d'entraîner une décharge électrique et de
reposition the actuator hub when using the manual
provoquer des blessures graves, voire
override feature.
mortelles.
IMPORTANT: Applying excessive torque to the
manual override or operating the manual override
with a power tool may damage the internal
components of the actuator and cause premature
failure.

To reposition the actuator hub, proceed as follows:
1. De-energize the actuator.
2. Insert the hex end of the manual override crank
into the manual override adjustment point on the
face of the actuator.
3. Rotate the manual override crank in the direction
indicated by the arrow on the label.

VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation 9
Instructions
CAUTION: Risk of Property Damage.

!
Floating Control, Four Wire
Do not apply power to the system before
RA RA
checking all wiring connections. Short DA DA
circuited or improperly connected wires BLK RED GRY ORN
2 3 4
may result in permanent damage to the 1

equipment.
MISE EN GARDE : Risque de dégâts
matériels.
Ne pas mettre le système sous tension
~
avant d'avoir vérifié tous les raccords de 24 VAC
- + 24 VDC
câblage. Des fils formant un court-circuit
ou connectés de façon incorrecte
risquent d'endommager Open/Close, Single Wire Control

irrémédiablement l'équipement. RA RA
DA DA
BLK RED GRY ORN
CAUTION: Risk of Property Damage. 1 2 3 4

! Insulate and secure each unused wire
lead before applying power to the
actuator. Failure to insulate and secure
each unused wire lead may result in
property damage. ~ 24 VAC

MISE EN GARDE : Risque de dégâts - + 24 VDC

matériels.
Isoler et protéger chaque fil non utilisé
avant de mettre l'actuator sous tension. On/Off Control, Two Wire

Le non-respect de cette obligation RA RA
DA DA
d'isolation et de protection de chaque fil BLK RED GRY ORN
non utilisé risque d'entraîner des dégâts 1 2 3 4

matériels.

IMPORTANT: Make all wiring connections in
accordance with the National Electrical Code and
local regulations. Use proper Electrostatic Discharge ~ 24 VAC
(ESD) precautions during installation and servicing - + 24 VDC

to avoid damaging the electronic circuits of the
actuator. Floating Control, Multiple Actuators with One Transformer
RA RA RA RA
See Figure 19 to wire the applicable VA9208-AGx-x DA DA DA DA
Series model. BLK RED GRY ORN BLK RED GRY ORN
1 2 3 4 1 2 3 4

FIG:VA9208-AGx_cntrlwir
~ 24 VAC
- + 24 VDC

Figure 19: Control wiring diagrams

IMPORTANT: Multiple VA9208-AGx-x Actuators
must be on independent loads.

10 VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation
Instructions
Figure 20 shows the optional Auxiliary Switch Wiring. Setup and adjustments
Mode selection switch
Actuators have an external mode selection switch to
reverse control logic. The switch is accessible from
both A and B sides of the actuator as illustrated in
Figure 22. Actuators are delivered in Direct Acting (DA)
mode and can be switched by the user to Reverse
Acting (RA) mode.

FIG:AGx_modsel
DA RA RA DA

Side A of Actuator Side B of Actuator

FIG: AX_SWCTH
COM NC NO COM NC NO
Figure 22: Mode selection

Control response
Figure 20: Optional auxiliary switch wiring
The installation side of the actuator and the position of
Using conduit the mode selection switch combine to determine
control response from the actuator. See Figure 23.
All VA9208 Series Actuators accept 3/8 in. (10 mm)
trade size flexible metal conduit. Installation Side

Control Inputs Mode Selection Switch
GRY ORN
3 4

FIG:VA92xxAGx_CtrlRspns
Figure 21: Adding flexible metal conduit

1. Feed the actuator cables through the field-supplied
conduit.
2. Push the conduit into the holes in the actuator and Figure 23: Control response
secure it with the supplied 10-32 x 9/16 in. screws,
as illustrated in Figure 21. The product label marks Auxiliary switch (VA9208-xxC-3 models)
the position of holes for the screws. Drive the The VA9208-xxC-3 models include two integral
screws through the product label in the marked auxiliary switches with a switch adjuster accessible on
positions. Drive the screwhead flush with the plate either face of the actuator (Figure 5). The factory
to secure the conduit. setting for Auxiliary Switch No. 1 is 83% closing, and
the nominal setting for Auxiliary Switch No. 2 is 10%
IMPORTANT: Careful workmanship is required to
opening (relative to the 0 to 100% rotation range as
secure flexible metal conduit. Cut the conduit end
printed on the product label). See the Technical
perpendicular to its axis. Insert the cut end into the
specifications table for the auxiliary switch ratings.
bottom of the holes in the actuator and hold the
conduit in place while securing it with the screws
provided. Check a completed installation by pulling
on the conduit to ensure its retention.

VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation 11
Instructions
2. Rotate the switch adjuster until it points to the
desired switch point.
CAUTION: Risk of Property Damage.

! Insulate and secure each unused wire
lead before applying power to the
actuator. Failure to insulate and secure
each unused wire lead may result in
property damage.
MISE EN GARDE : Risque de dégâts
matériels.
Isoler et protéger chaque fil non utilisé
avant de mettre l'actuator sous tension.
Le non-respect de cette obligation FIG:SW _TRP

d'isolation et de protection de chaque fil
non utilisé risque d'entraîner des dégâts Figure 24: Switch trip point settings
matériels.
3. Connect Auxiliary Switch No. 2 to a power source
The switch point of Auxiliary Switch No. 1 is fixed. The or an ohmmeter and apply power to the actuator.
switch point of Auxiliary Switch No. 2 is independently The actuator moves to the fully open position and
and continuously adjustable from 74 to 5% position. holds while power is applied.
For the most accurate switch positioning, see Figure 24
and use the method in the following example. To 4. Observe the switch point. If required, repeat Step 1
change the switch point of Auxiliary Switch No. 2, through Step 3.
proceed as follows: Repair information
1. Position the actuator in the full spring return A number of replacement parts are available; see
position. Table 3 for more details. If a VA9208 Series Electric
Spring Return Actuator fails to operate within its
Note: The switch is factory set to trip when the
specifications, replace the unit. For a replacement
actuator reaches the 10% position.
electric actuator, contact the nearest Johnson Controls
representative.

12 VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation
Instructions
Technical specifications
VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Actuators (Part 1 of 2 )
Power -AGx models AC 24 V (AC 19.2 V to 28.8 V) at 50/60 Hz: Class 2 (North America) or Safety
Requirements Extra-Low Voltage (SELV) (Europe), 7.9 VA Running, 5.5 VA Holding Position
DC 24 V (DC 21.6 V to 28.8 V): Class 2 (North America) or SELV (Europe)
3.5 W running, 1.9 W holding position
Minimum transformer size: 8 VA per actuator
Input signal/ -AGx models AC 19.2 to 28.8 V at 50/60 Hz or DC 24 V +20%/-10% Class 2 (North America)
adjustments or SELV (Europe) minimum pulse width: 500 ms
Control input -AGx models 3,000 ohm control inputs
impedance
Auxiliary switch -xxC models Two Single-Pole, Double-Throw (SPDT), double-insulated switches with gold
rating over silver contacts:
AC 24 V, 50 VA pilot duty
AC 120 V, 5.8 A resistive, 1/4 hp, 275 VA pilot duty
AC 240 V, 5.0 A resistive, 1/4 hp, 275 VA pilot duty
Spring return Direction is selectable with mounting position of actuator:
Actuator face labeled A is away from valve: CCW spring return
Actuator face labeled B is away from valve: CW spring return
Rated torque Power on 70 lb·in. (8 N·m) all operating temperatures
(running)
Power off 70 lb·in. (8 N·m) all operating temperatures
(spring returning)
Rotation range Maximum full stroke: 95°
Rotation time for Power on 150 seconds for 0 to 70 lb·in. (8 N·m) load, at all operating conditions
90 degrees of (running)
travel
Power off 17 to 25 seconds for 0 to 70 lb·in. (8 N·m) load, at room temperature
(spring returning) 22 seconds nominal at full rated load
94 seconds maximum with 70 lb·in. (8 N·m) load, at -40°F (-40°C)
Life cycles 60,000 full stroke cycles with 70 lb·in. (8 N·m) load
1,500,000 repositions with 70 lb·in. (8 N·m) load
Audible noise Power on <35 dBA at 70 lb·in. (8 N·m) load, at a distance of 39-13/32 in. (1 m)
rating (running)
Power on <20 dBA at a distance of 39-13/32 in. (1 m)
(holding)
Power off <52 dBA at 70 lb·in. (8 N·m) load, at a distance of 39-13/32 in. (1 m)
(spring returning)
Electrical AGx-3 models 48 in. (1.2 m) UL 758 Type AWM halogen free cable with 18 AWG (0.85 mm2)
connections conductors and 1/4 in. (6 mm) ferrule ends
AGx-2 models 36 in. (0.9 m) UL 444 Type CMP plenum rated cable with 19 AWG (0.75 mm2)
conductors and 1/4 in. (6 mm) ferrule ends
Auxiliary switches 48 in. (1.2 m) UL 758 Type AWM halogen free cable with 18 AWG (0.85 mm2)
(-xxC models) conductors and 1/4 in. (6 mm) ferrule ends
Conduit connections Integral connectors for 3/8 in. (10 mm) flexible metal conduit
Fluid VG12x1 and VG18x1 23 to 203°F (-5 to 95°C), not rated for steam service
temperature Series
limits
VG12x5 and VG18x5 -22 to 212°F (-30 to 100°C), not rated for steam service
Series
VG12x5 and VG18x5 -22 to 284°F (-30 to 140°C) water; 15 psig (103 kPa) at 250°F (121°C)
Series with saturated steam
M9000-561 Thermal
Barrier installed

VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation 13
Instructions
VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Actuators (Part 2 of 2 )
Ambient Standard operating -40 to 140°F (-40 to 60°C); 90% RH maximum, noncondensing
conditions
Storage -40 to 185°F (-40 to 85°C); 95% RH maximum, noncondensing
Enclosure rating NEMA 2 (IP54) for all mounting directions
Compliance United States UL Listed, CCN XAPX, File E27734; to UL 60730-1A: 2003-08, Ed. 3.1,
Automatic Electrical Controls for Household and Similar Use; and
UL 60730-2-14: 2002-02, Ed. 1, Part 2 Particular Requirements for Electric
Actuators
Canada UL Listed, CCN XAPX7, File E27734; to UL 60730-1:02-CAN/CSA: July 2002,
3rd Ed., Automatic Electrical Controls for Household and Similar Use; and
CSA C22.2 No. 24-93 Temperature Indicating and Regulating Equipment
Europe CE Mark – Johnson Controls declares that this product is in compliance with
the essential requirements and other relevant provisions of the EMC Directive
and the Low Voltage Directive.
Australia and New RCM Mark, Australia/NZ Emissions Compliant
Zealand
Shipping weight -AGA models 3.5 lb (1.6 kg)
-AGC models 3.9 lb (1.8 kg)
UK Single Point of Contact: European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact:
JOHNSON CONTROLS JOHNSON CONTROLS JOHNSON CONTROLS JOHNSON CONTROLS
TYCO PARK GRIMSHAW LANE VOLTAWEG 20 5757 N GREEN BAY AVE C/O CONTROLS PRODUCT MANAGEMENT
MANCHESTER M40 2WL 6101 XK ECHT GLENDALE WI 53209 NO. 32 CHANGJIANG NEW DISTRICT
UNITED KINGDOM THE NETHERLANDS USA WUXI JIANGSU PROVINCE 214028
CHINA

Building Technologies & Solutions
5757 N Green Bay Ave, Glendale, WI 53209
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls
All other marks herein are the marks of their respective owners. © 2022 Johnson Controls

14 VA9208-AGx-x Series On/Off and Floating Point Electric Spring Return Valve Actuators Installation
Instructions
Published in U.S.A. www.johnsoncontrols.com

Позиції каталогу з цим документом

Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.