| Вид документа | Інструкція з монтажу |
|---|---|
| Виробник | JCI |
| Код документа | security-control-panel-assembly-mounted-in-a-30-in-x-42-in-enclosure |
| Група обладнання | Security Control Panel |
| Сторінок | 2 |
| Мова документа | англійська |
| Розмір файлу | 0.2 МБ |
О чём документ
Инструкция по монтажу и подключению заводской охранно-контрольной панели, смонтированной в стальном шкафу 30 × 42 дюйма с ключом и датчиком вскрытия двери. Внутри шкафа предустановлены сетевой контроллер CK721-A и/или до восьми двухдверных модулей RDR2S-A (S300-DIN-RDR2SA) и блоки питания. Документ описывает состав комплектации, требования к кабелям, подключение питания и аккумуляторов.
Ключевые характеристики
| Параметр | Значение |
|---|---|
| Габариты (Ш × В × Г) | 30 in. × 42 in. × 6.62 in. (76,2 × 107 × 16,8 см) |
| Степень защиты шкафа | NEMA Type 1 |
| Питание SPA1B400-2E10 | 120 VAC, 3.6 A, 50/60 Hz |
| Питание SPA1B600-3E10 | 120 VAC, 5.4 A, 50/60 Hz |
| Питание SPA1B800-3E10 | 120 VAC, 5.4 A, 50/60 Hz |
| Блоки питания | S300-DIN-L-PS, 24 VDC, 5 A (2 или 3 шт. по модели) |
| Резервное питание (опция) | S300-BAT: 2× PowerSonic PS-1270, 12 VDC, 7 Ah, гелевые, на каждый БП |
| Рабочие условия | 32…122 °F (0…50 °C), 10…85 % RH, без конденсации |
| Условия хранения | −4…158 °F (−20…70 °C), 5…95 % RH, без конденсации |
| Межцентровое расстояние крепёжных отверстий | 22.75 in. (57,8 см) по горизонтали, 39.88 in. (101,3 см) по вертикали; диаметр 0.436 in. (1,1 см) |
| Состав SPA1B400-2E10 | CK721-A + 4× RDR2S-A + 2 БП |
| Состав SPA1B600-3E10 | CK721-A + 6× RDR2S-A + 3 БП |
| Состав SPA1B800-3E10 | CK721-A + 8× RDR2S-A + 3 БП |
| Уровни UL 294 (все модели) | Destructive Attack — Level I; Line Security — Level II; Endurance — Level IV; Standby Power — Level II |
| Соответствие | UL 294, UL 1076, FCC Part 15 Class B, CAN ICES-3 (B), cUL по ULC/ORD-C1076, CE (EMC + LVD) |
Что внутри документа
- Applications — назначение панели и состав поставки (шкаф, контроллер, модули, БП)
- Selection Chart / Product Code — таблица кодов заказа и комплектации моделей
- Cable Requirements — таблица типов кабелей и максимальных длин сегментов
- Mounting and Connecting the Panels — монтаж панели на стену в зоне ограниченного доступа
- AC Power Connection — подключение сетевого питания к клеммной колодке TB-1
- S300-BAT Battery Connection — подключение и замена аккумуляторов
- Field Devices — отсылка к документации CK721-A и RDR2S-A, требование отдельного питания дверного замка
- UL 294 Performance Levels — уровни характеристик по UL 294
- Repair Information — контакты техподдержки и каталог компонентов (LIT-1900572)
Быстрый старт
- Смонтируйте панель на стене в помещении с ограниченным доступом, сняв заднюю плату перед креплением и установив её обратно после монтажа.
- Проверьте, что дверь открывается полностью, а воздушный поток над поверхностями не затруднён.
- Заведите сетевую проводку 120 VAC через кабельный ввод к клеммной колодке TB-1 (L — Line, N — Neutral, G — Ground).
- Подключите кабели периферии согласно таблице Cable Requirements (RS485, ICOM, Ethernet, RS232, линии считывателей).
- Только после завершения всей проводки подключите кабель DC питания к модулям.
- При использовании опции подключите аккумуляторы S300-BAT, соблюдая полярность (RED +, BLK −, WHT).
Частые вопросы
- Какие кабели использовать для линии RS485 к модулю RDR2S-A?
- Listed, 18 AWG, 3-проводной, многожильный, экранированный, медный; максимальная длина сегмента 4,000 ft (1 219 м). Экранирование не обязательно, но настоятельно рекомендуется.
- Какой кабель допускается для Ethernet-подключения контроллера CK721-A?
- Listed, Category 5, 24 AWG, solid, 2- или 4-парный; максимальная длина 354 ft (100 м). Кабель, разъём RJ45 и обжимной инструмент предоставляет заказчик.
- Какие аккумуляторы использует панель и как часто их менять?
- По два sealed lead acid аккумулятора PowerSonic PS-1270 (12 VDC, 7 Ah) на каждый блок питания. Замена — каждые три года, а также после любого сбоя питания по переменному току, независимо от того, были ли аккумуляторы в эксплуатации.
- Можно ли запитать дверной замок (door strike) от БП шкафа?
- Нет. Для питания door strike используйте отдельный трансформатор или источник Class 2; подключение замка к блоку питания шкафа категорически запрещено.
- Можно ли прокладывать сигнальные кабели в одном лотке/трубе с силовыми?
- Нет, все информационные кабели должны быть физически отделены от силовых линий; в одну трубу с силовыми кабелями или кабелями замков (напряжение выше 42 V, магнитные замки без подавления EMI) их не закладывать. Монтаж — по NFPA 70 (National Electrical Code) или, в Канаде, Canadian Electric Code C22.1.
Текст документа
Security Control Panel Assembly
Mounted in a 30 in. x 42 in. Enclosure Part No. 24-10613-47, Rev. C
Issued December 2017
Installation Instructions
SPA1B400-2E10, SPA1B600-3E10, SPA1B800-3E10
Refer to the QuickLIT Web site for the most up-to-date version of this document.
Applications Parts Included
The 30 in. x 42 in. Security Control Panel is a pre-wired, • 30 in. x 42 in. (76.2 cm x 107 cm) enclosure, Type 1 with keyed
preassembled standard control panel and enclosure that contains a lock, door tamper switch, and battery support brackets
CK721-A network controller and/or S300-DIN-RDR2SA (also called • CK721-A network controller and up to eight RDR2S-A two-door
RDR2S-A) modules. The control panel is shipped complete, mounted interface modules
• Two or three S300-DIN-L-PS 24 VDC, 5 A power supplies
in a steel enclosure. The panel is equipped with the required number
of 120 VAC/24 VDC power supplies. The power supply has
Uninterruptible Power Supply (UPS) capability with the addition of
factory-wired gel cell batteries (S300-BAT), which are sold separately.
These enclosures are designed specifically for security control
requirements, with battery brackets that do not need to be removed to
install the batteries, a lift-off door, a pre-wired door tamper switch, and
a lockable door with key. Space is reserved on specific models for the
addition of future components.
Repair Information
If the Security Control Panel Assembly fails to operate within its
specifications, replace the failed component. Contact Global Security
Solutions Technical Support at (866) 893-0423 or (414) 524-1214, or
by email at support.globalsecuritysolutions@jci.com. End users can
contact their local branch or authorized dealer. For the nearest office,
visit http://www.johnsoncontrols.com/location-finder.
Refer to the Security Enclosure Components Catalog Page
(LIT-1900572) to order components separately.
Figure 1: Security Control Panel Mounted in a
30 in. x 42 in. Enclosure
Cable Requirements
Description Recommended Cable Type1, 2 Maximum Segment Length
CK721-A: RS485A, RS485B Listed, 22 AWG, stranded, copper, hook-up wire Limited to within cabinet.
RDR2S-A: RS485+/-
Listed, 18 AWG, 3-conductor, stranded, shielded, copper 4,000 ft (1,219 m) maximum
CK721-A: ICOM1, ICOM2 Belden® 8442, 22 AWG, 1 twisted pair, stranded, 500 ft (152 m)
RDR2S-A: Door Contact unshielded, copper
CK721-A: OUT1 Belden 9740, 18 AWG, 1 twisted pair, stranded, Depends on power requirements of the device. Voltage to
RDR2S-A: Door Strike, Shunt unshielded, copper the device must not be reduced more than 10% over the
18 AWG wire, measured when energized.
Request to Exit (RDR2S-A only) Belden 8442, 22 AWG, 1 twisted pair, stranded, 500 ft (152 m)
unshielded, copper
Reader Power (RDR2S-A only) Belden 9740, 18 AWG, 1 twisted pair, stranded, Refer to reader manufacturer’s specification for power
unshielded, copper requirements.
Reader Data0/Data1 Belden 9744, 22 AWG, 2 twisted pairs, stranded, 500 ft (152 m). Refer to reader manufacturer’s
(RDR2S-A only) unshielded, copper specification for data requirements.
RS232 A, RS232 B Listed DB9 F/F AT Null Modem cable 25 ft (7 m). Cable must remain in the same room as the
CK721-A.
Ethernet Listed, Category 5, 24 AWG, solid, 2 pair or 4 pair type 354 ft (100 m). Cable, RJ45 connector, and RJ45 crimp
tool to be supplied by customer.
1. All data cables should be physically separated from power lines. If conduit is used, do not run data cables in the same conduit as power cables or certain door
strike cables, such as strike voltage greater than 42 V or magnetic door locks without Electromagnetic Interference (EMI) suppression. All cables must conform
with National Electrical Code, NFPA 70; or for Canadian installations, refer to the Canadian Electric Code C22.1.
2. Shielded cable is not required but is strongly recommended to minimize the effects of electromagnetic interference or radio frequency noise.
UL 294 Performance Levels
Destructive Attack Line Security Endurance Standby Power
SPA1B400-2E10 Level I Level II Level IV Level II
SPA1B600-3E10 Level I Level II Level IV Level II
SPA1B800-3E10 Level I Level II Level IV Level II
Security Control Panel Assembly Mounted in a 30 in. x 42 in. Enclosure Installation Instructions 1
Mounting and Connecting the Panels Product Code Description
Number
• Mount the panel on a wall or other mounting surface located in a
restricted-access area. SPA1B600-3E10 30 in. x 42 in. (76.2 cm x 10.7 cm) security control
• The horizontal distance between the mounting holes is 22.75 in. panel with CK721-A controller, six RDR2S-A
(57.8 cm); the vertical distance is 39.88 in. (101.3 cm). Mounting modules, and three power supplies
hole diameter is 0.436 in. (1.1 cm). SPA1B800-3E10 30 in. x 42 in. (76.2 cm x 10.7 cm) security control
• Ensure the door can swing fully open. panel with CK721-A controller, eight RDR2S-A
• Mount the panel in a location where airflow is uninhibited over the modules, and three power supplies
exposed surfaces.
• Remove the back plate before securing the panel to the mounting
surface and reinstall it when mounting is complete. Technical Specifications
AC Power Connection Security Control Panel Assembly Mounted in a 30 in. x 42 in.
Enclosure
• Put the AC Wired at
power wiring Electrical Rating SPA1B400-2E10: 120 VAC, 3.6 A, 50/60 Hz
To AC power
the factory
BLU
G
through a N SPA1B600-3E10: 120 VAC, 5.4 A, 50/60 Hz
BRN
BLU
knockout. L N L L = Line SPA1B800-3E10: 120 VAC, 5.4 A, 50/60 Hz
source
BRN
• Connect the AC N = Neutral
TB-1 Power supply G = Ground Enclosure Rating NEMA Type 1
power wiring to
terminal block Ambient Operating 32 to 122°F (0 to 50°C), 10 to 85% RH,
TB-1. Condition noncondensing
• Do not connect the DC power cable to the module until all wiring is
complete Dimensions (Width 30 in. x 42 in. x 6.62 in.
x Height x Depth) (76.2 cm x 107 cm x 16.8 cm)
WARNING: Risk of Electric Shock. Ambient Storage -4 to 158°F (-20 to 70°C), 5 to 95% RH,
Condition noncondensing
!
Disconnect the power supply before making
electrical connections. Contact with components Compliance United States:
carrying hazardous voltage can cause electric shock UL Listed under UL 1076 for Proprietary Burglar
Alarm Units and Systems, and under UL 294 for
and may result in severe personal injury or death. Access Control Systems Units;
This equipment has been tested and found to
S300-BAT Battery Connection comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits
The optional S300-BAT feature are designed to provide reasonable protection
RED
WHT BLK
uses two PowerSonic, Model against harmful interference in a residential
PS-1270, 12 VDC, 7 Ah, sealed + - + - + - + - G N L installation. This equipment generates, uses and
lead acid batteries per power DC can radiate radio frequency energy and, if not
BAT
HIGH
supply. The batteries should be B-1A B-1B OUT VOLT
AGE installed and used in accordance with the
replaced every three years to instructions, may cause harmful interference to
PS-1
ensure proper operation. radio communications. However, there is no
The RED (+), BLK (-), and guarantee that interference will not occur in a
RED
WHT BLK
WHT cables are provided with particular installation. If this equipment does cause
the enclosure. + - + - harmful interference to radio or television reception,
+ - + - G N L
Replace the batteries whether DC
which can be determined by turning the equipment
BAT
HIGH
or not they have been placed B-2A B-2B OUT VOLT
AGE
off and on, the user is encouraged to try to correct
into use by an AC power the interference by one or more of the following
failure. Observe the polarity PS-2 measures:
when connecting the batteries. • Reorient or relocate the receiving antenna.
RED
WHT BLK • Increase the separation between the equipment
Field Devices
and receiver.
For information on wiring the + - + - + - + - GNL • Connect the equipment into an outlet on a circuit
DC
BAT
HIGH
CK721-A controller or B-3A B-3B OUT VOLT different from that to which the receiver is
the RDR2S-A module, refer to AGE
connected.
the documentation provided PS-3 • Consult the dealer or an experienced radio/TV
with these devices. technician for help.
Use a separate Class 2 transformer or power supply for door strike The user is cautioned that changes and
power. Under no circumstances connect a door strike to the modifications made to the equipment without
enclosure power supply. approval of the manufacturer could void the user's
authority to operate this equipment.
Selection Chart
Canada:
Product Code Description CAN ICES-3 (B)/NMB-3(B);
Number cUL Listed under ULC/ORD-C1076 Proprietary
Burglar Alarm Units and Systems
SPA1B400-2E10 30 in. x 42 in. (76.2 cm x 10.7 cm) security control
panel with CK721-A controller, four RDR2S-A Europe:
modules, and two power supplies CE Mark – Johnson Controls, declares that this
product is in compliance with the EMC Directive and
the Low Voltage Directive.
(SPA1B400-2E10 only)
Building Technologies & Solutions
507 E. Michigan Street, Milwaukee, WI 53202
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls
All other marks herein are the marks of their respective owners. © 2017 Johnson Controls
2 Security Control Panel Assembly Mounted in a 30 in. x 42 in. Enclosure Installation Instructions
Published in U.S.A. www.johnsoncontrols.comПозиції каталогу з цим документом
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.