| Вид документа | Каталожна сторінка |
|---|---|
| Виробник | JCI |
| Код документа | m9106-xgx-2-series-electric-non-spring-return-actuators-catalog-page |
| Група обладнання | M9106 |
| Сторінок | 6 |
| Мова документа | англійська |
| Розмір файлу | 0.7 МБ |
Текст документа
M9106-xGx-2 Series Electric Non-
Spring-Return Actuators Catalog
Page
LIT-1900118
2019-10-09
Description
The M9106-xGx-2 Series direct-mount electric actuators
operate on AC 24 V power and are available for use with
on/off, floating, or proportional controllers. These non-
spring-return actuators are easily installed on a VAV box,
a damper with a round shaft up to 1/2 in. (13 mm) in
diameter, or a square shaft up to 3/8 in. (10 mm). The
M9106 with an M9000-520 linkage can also be used to
position VG1000 Series 1/2 in. (DN15) to1-1/2 in. (DN40)
ball valves.
The M9106 Series models have 53 lb·in (6 N·m) running
torque. These actuators have a nominal 60-second travel
time for 90° of rotation at 60 Hz (72 seconds at 50 Hz)
with a load-independent rotation time.
The M9106-xGC-2 models are available with integral
auxiliary switches to perform switching functions at
any angle within the selected rotation range. The -GGx
models feature DC 0(2) to 10 V position feedback, and
the -AGF models provide 10,000 ohm position feedback.
M9106-xGx-2
Features Applications
• simple direct coupling reduces installation and The M9106 actuators are used to position balancing,
commissioning time and improves reliability control, round, and zone dampers in typical HVAC
by eliminating damper linkages; single screw applications. The M9106 can also be used with an
coupling provides three-point shaft gripping M9000-520 linkage to control 1/2 in. (DN15) to 1-1/2
in. (DN40) VG1000 Series ball valves. The M9106
• designed for zone damper and ball valve actuator Series actuator mounts directly on the duct surface,
applications round damper, or small rectangular damper with
an anti-rotation bracket and two sheet metal screws
• small, compact design allows installation in tight- (included). Additional linkages or couplers are not
fitting locations required.
• on/off, floating, and proportional control inputs Refer to the damper or VAV box manufacturer’s
information to select the proper timing for the
• 60-second running time at 60 Hz actuator. Refer to the appropriate application note
for specific wiring diagrams and information.
• long life brushless synchronous drive motor
Refer to the M9106-xGx-2 Electric Non-Spring-Return
technology provides constant running time Actuators Product Bulletin (LIT-2681123) or the M9106-
independent of load xGx-2 Electric Non-Spring-Return Actuators Installation
Instructions (Part No. 34-636-1085) for important
• robust 53 lb·in (6 N·m) torque rating
product application information.
• whisper quiet 35 dBA noise rating
• magnetic clutch provides over torque protection
Repair information
over the entire range of rotation If the M9106-xGx-2 Series Electric Actuator fails to
operate within its specifications, replace the unit.
• -4°F to 125°F (-20°C to 52°C) ambient temperature For a replacement actuator, contact the nearest
rating Johnson Controls® representative.
• 100,000 full stroke cycle, 2,500,000 reposition
rating
• manual gear release simplifies setup and field
adjustments
• 1/2 in. NPT threaded conduit opening meets
electrical code requirements and allows the use
of flexible armored cable
• position feedback (-GGX models) provides simple,
closed-loop control with accurate position sensing
• adjustable rotation stops allow application
versatility with 30 to 90° clockwise or
counterclockwise rotation
M9106-xGx-2 Series Electric Non-Spring-Return Actuators Catalog Page 2
Selection chart
Table 1: Selection chart
Code number Control type Torque / timing / voltage Auxiliary switches Comments
M9106-AGA-2
1 Floating 53 lb·in (6 N·m) None
60 seconds at 60 Hz
M9106-AGC-2 2-SPDT
AC 24 V 50/60 Hz
M9106-AGF-2 Floating with resistive feedback None 10,000 ohm feedback pot
M9106-GGA-2 DC 0(2) to 10 V None DC 0(2) to 10 V feedback
M9106-GGC-2 DC 0(4) to mA proportional 2-SPDT
M9106-IGA-2 On/off / floating with timeout None Adjustable timing 1, 1.5, 2, 5.5, or 11 minutes
M9106-IGC-2 2-SPDT
1 To avoid excessive wear or dive time on the motor for the -AGx models, use a controller and/or software that provides a time-out
function to remove the signal at the end of rotation (stall). The -GGx and -IGx models have an auto shutoff to avoid excessive wear
or drive time on the motor.
Accessories
Table 2: Accessories
Code number Description
CBL-2000-1 20 in. (0.5 m) wiring harness, UL accepted for plenum use, connects the M9106 and DPT-2015 to the VAV controller
CBL-2000-2 20 in. (0.5 m) plenum rated wiring harness
CBL-2000-3 72 in. (1.8 m) plenum rated wiring harness
DPT-2015-0 0 in. to 1.5 in. W.C. (0 Pa to 374 Pa) differential pressure transmitter
DMPR-KC003 Square head blade pin extension without bracket supplied with Johnson Controls CD-1300 dampers and may be ordered separately for all direct-mount
applications
DMPR-KC010 Adjustable blade position indicator switch kit with total switching load limited to 2,000 VA for the following applications:
Pilot duty: AC 24 V, 50 VA; AC 125/250/277 V, 125 VA
Motor load: AC 125/250/277 V, 1/3 hp
Resistive load: AC 125 V, 11 A; AC 250 V, 8 A; AC 277 V, 7 A (all maximum values)
DMPR-KC011 Hex head blade pin extension without bracket
DMPR-KC012 Hex head blade pin extension with bracket
DMPR-KC213 Damper jackshaft 1/2 in. diameter, 1 panel
DMPR-KC214 Damper jackshaft 1/2 in. diameter, 2 panel
M9000-105 Pluggable 3-terminal block
M9000-106 Pluggable 4-terminal block
M9000-160 Replacement anti-rotation bracket for M9106 Series actuators
M9000-520 Valve linkage kit for field mounting an M9106 Series actuator to a 1/2 in. (DN15) to 1-1/2 in. (DN40) VG1000 Series ball valve
Figure 1: Dimensions, in./mm
3 M9106-xGx-2 Series Electric Non-Spring-Return Actuators Catalog Page
Technical specifications
Table 3: Technical specifications
M9106-xGx-2 Series Electric Non-Spring-Return Actuators
Power requirement AGx: AC 20-30 V at 50/60 Hz, 2.5 VA supply, Class 2
IGx: AC 20-30 V at 50/60 Hz, 2.8 VA supply, Class 2
GGx: AC 20-30 V at 50/60 Hz, 3.2 VA supply, Class 2
Control type AGx: floating
IGx: on/off, floating
GGx: DC 0(2) to 10 V or DC 0(4) to 20 mA proportional
Input signal AGx and IGx: AC 20 to 30 V at 50/60 Hz
GGx: DC 0 to 10 V or DC 0(4) to 20 mA
Input signal adjustments: AGx and IGx: CW and COM Terminals, CW rotation; CCW and COM terminals, CCW rotation
GGx (voltage input or current input):
Jumper selectable: DC 0(2) to 10 V or DC 0(4) to 20 mA
Factory setting: DC 0 to 10 V, CW rotation with signal increase
Action is jumper selectable direct (CW) or reverse (CCW) with signal increase.
Input impedance AGx: 200 ohms, nominal
IGx: 160 ohms, nominal
GGx: voltage input, 150,000 ohms; current input, 500 ohms
Feedback signal AGF: 10,000 ohm potentiometer, 1 W
GGx: DC 0 to 10 V or DC 2 to 10 V for 90° (1 mA);
Corresponds to input signal span selection
Auxiliary switch rating xGC: two single-pole, double-throw (SPDT) switches rated at AC 24 V, 1.5 A inductive, 3.0 A resistive, 35 VA maximum per switch,
Class 2
Torque rating 1, 1.5, and 2 minute settings: 53 lb·in (6 N·m)
5.5 and 11 minute settings: 35 lb·in (4 N·m)
Cycle life 100,000 full cycles; 2,500,000 repositions rated at 53 lb·in (6 N·m)
Audible noise rating 35 dBA maximum at 39.4 in. (1 m)
Rotation range Adjustable from 30° to 90°, CW or CCW
Rotation time IGx: adjustable with switch settings (factory set for 1 minute) 60, 90, 120, 330, or 660 seconds (1, 1.5, 2, 5.5 or 11 minutes) at 60 Hz
and 72, 108, 144, 396, or 792 seconds at 50 Hz
All other models: nominal 60 seconds at 60 Hz and 72 seconds at 50 Hz for 90°
Electrical connection 1/4 in. spade terminals (to order optional pluggable terminal blocks, see Accessories)
Mechanical connection 3/8 in. to 1/2 in. (10 mm to 12.7 mm) round shaft or 3/8 in. (10 mm) square shaft
Enclosure rating NEMA 2, IP32
Ambient operating rating -4°F to 125°F (-20°C to 52°C); 90% RH maximum, noncondensing
Ambient storage rating IGx: -40°F to 186°F (-40°C to 86°C); 90% RH maximum, noncondensing
All other models: -40°F to 176°F (-40°C to 80°C); 90% RH maximum, noncondensing
Shipping weight 2.4 lb (1.08 kg)
Compliance United States UL 873 Listed, File E27734, CCN XAPX
Canada CSA C22.2 No. 139 Certified, File LR85083, Class 3221 02
Europe CE Mark - Johnson Controls declares that this product is in compliance with the essential requirements and other relevant
provisions of the EMC Directive 2004/108/EC.
Product warranty
This product is covered by a limited
warranty, details of which can be found at
www.johnsoncontrols.com/buildingswarranty.
M9106-xGx-2 Series Electric Non-Spring-Return Actuators Catalog Page 4
Single point of contact
APAC Europe NA/SA
JOHNSON CONTROLS JOHNSON CONTROLS JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT WESTENDHOF 3 507 E MICHIGAN ST
NO. 32 CHANGJIJANG RD NEW DISTRICT 45143 ESSEN MILWAUKEE WI 53202
WUXI JIANGSU PROVINCE 214028 GERMANY USA
CHINA
5 M9106-xGx-2 Series Electric Non-Spring-Return Actuators Catalog Page
© 2019 Johnson Controls. All rights reserved. All specifications and other information shown were current
as of document revision and are subject to change without notice.
www.johnsoncontrols.comПозиції каталогу з цим документом
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.