| Вид документа | Технічний бюлетень |
|---|---|
| Виробник | JCI |
| Код документа | m9106-agx-2n0x-series-electric-non-spring-return-actuators-submittal-bulletin |
| Група обладнання | M9106 |
| Сторінок | 4 |
| Мова документа | англійська |
| Розмір файлу | 0.1 МБ |
Текст документа
Submittal Bulletin
Issue Date October 2017
M9106-AGx-2N0x Series Electric
Non-spring Return Actuators
The M9106-AGA-2N0x synchronous motor-driven
actuators provide floating (3-wire) control and are
easily installed on a Variable Air Volume (VAV) box.
They may also be installed on a small or
medium-sized damper with a round shaft up to 1/2 in.
(13 mm) in diameter or a 3/8 in. (10 mm) square shaft.
These compact, non-spring return actuators have a
53 lb∙in (6 N∙m) running torque in a compact,
easy-to-install package. The actuators are available
with either a nominal 60-second travel time at 60 Hz
(72 seconds at 50 Hz) or a nominal 120-second travel
time at 60 Hz (144 seconds at 50 Hz) for 90° of
rotation.
The M9106-AGS-2N02 Actuator/Transmitter combines
an M9106-AGA-2N02 with a prewired DPT-2015
Differential Pressure Transmitter that has a
0 to 1.5 in. W.C. (0 to 374 Pa) differential pressure Figure 1: M9106-AGS-2N02 Non-spring
range. Return Actuator
Features and Benefits
35 dBA Rating Meets audible requirements for open ceilings
Synchronous Drive Provides constant rotation time independent
of load
Direct Shaft Mount with Simplifies installation and provides 3-point
Single-Screw Coupler shaft gripping
Magnetic Clutch Provides torque protection for the actuator
and damper
Adjustable Rotation Stops Allow application versatility with 30 to 90°
Clockwise (CW) or Counterclockwise (CCW)
rotation
Manual Gear Release Simplifies setup and field adjustments
Screw Terminal Connection Makes wiring easy
© 2017 Johnson Controls, Inc. 1
Code No. LIT-1201447 www.johnsoncontrols.com
Application
IMPORTANT: This device is not designed or A 24 VAC signal from the controller to the CW or
intended to be used in or near environments where CCW terminal of the actuator causes the motor to
explosive vapors or gases could be present, or rotate in the proper direction and moves the
environments where substances corrosive to the damper blades open or closed. When the controller
device’s internal components could be present. stops sending the signal, the actuator remains in
place.
The actuators are used to position balancing, control, Note: To avoid excessive wear or drive time on the
round, and zone dampers in typical Heating, motor, use a controller and/or software that provides a
Ventilating, and Air Conditioning (HVAC) applications. time-out function to remove the signal at the end of
They are also used to position the blades in a rotation (stall).
VAV box.
The -2N01 model rotates at a nominal rate of 1.5° per
The actuators mount directly to the surface of a second (90° in 1 minute). The -2N02 models rotate at
VAV box, round damper, or small rectangular damper a nominal rate of 0.75° per second (90° in 2 minutes).
with a single No. 10 self-drilling sheet metal screw Rotation is field adjustable from 30 to 90°. Actual
(included). There are no additional linkages or rotation time for actuators using less than 90° rotation
couplers required. Clearly labeled electrical terminals must be determined, and that value must be used with
simplify installation. Refer to the damper or VAV box the controller software. For example, the travel time for
manufacturer’s information to select the proper timing 60° rotation is 40 seconds for the -2N01 model and
for the actuator. 80 seconds for a -2N02.
Note: The damper rotation time must be defined at The M9106-AGS-2N02 is prewired with the 20 in.
the controller, and the damper point definition must (0.5 m) CBL-2000-1 Wiring Harness and the
match the rotation time of the actuator. DPT-2015, which is connected to the airflow pickup
device of the VAV box. The DPT-2015 measures
Operation differential pressure and generates a proportional
0.5 to 4.5 VDC signal. The voltage signal from the
IMPORTANT: The M9106-AGx-2N0x Series DPT-2015 is read by the VAV controller and converted
actuators are intended to control equipment under to airflow in cubic feet per minute (cfm). The wiring
normal operating conditions. Where failure or harness is used to connect the transmitter and
malfunction of an M9106-AGx-2N0x actuator could actuator to the VAV Series controller for simplified
lead to an abnormal operating condition that could installation.
cause personal injury or damage to the equipment or
other property, other devices (limit or safety Only zero calibration is required, which is performed
controls), or systems (alarm or supervisory) intended within the controller. The VAV controller must be
to warn of, or protect against, failure or malfunction provided with the correct K factor and VAV box size to
of the M9106-AGx-2N0x actuator must be perform the calculations. Refer to Appendix B: VAV
incorporated into and maintained as part of the Controller Flow Calculation Constants (LIT-6375185).
control system. M9106-AGx-2N0x models are replacements for the
one- and two-minute EDA-2040 and ATP-2040
When combined with a VAV controller, the actuator
actuators. To replace the EDA-2040 or ATP-2040
provides reliable, integrated damper control. See the
originally supplied with an EDA-2040-102 switch kit,
M9106-AGx-2N0x Series Electric Non-spring Return
use either an:
Actuators Application Note (LIT-2681116) for various
configurations with and without the DPT-2015 • M9106-AGx-2N0x actuator with the DMPR-KC010
differential pressure transmitter. switch kit (See Table 1.)
or
• M9106-AGC-2 actuator. See the M9106-xGx-2
Series Electric Non-spring Return Actuators
Product Bulletin (LIT-2681123) and M9106-xGx-2
Series Electric Non-spring Return Actuators
Installation Instructions (Part No. 34-636-1085) for
more information.
2 M9106-AGx-2N0x Series Electric Non-spring Return Actuators Submittal Bulletin
Ordering Information
Table 1: Actuator Models and Accessories
Product Code Number Description
M9106-AGA-2N01 Electric actuator (1-minute rotation time)
M9106-AGA-2N02 Electric actuator (2-minute rotation time)
M9106-AGS-2N02 Electric actuator (2-minute rotation time) includes the DPT-2015 and CBL-2000-1
CBL-2000-1 20 in. (0.5 m) wiring harness, Underwriters Laboratories®, Inc. (UL) accepted for plenum use,
supplied with the M9106-AGS-2N02 and may be ordered separately; connects the M9106 and
DPT-2015 to the VAV controller
CBL-2000-2 20 in. (0.5 m) plenum-rated wiring harness
CBL-2000-3 72 in. (1.8 m) plenum-rated wiring harness
DPT-2015-0 0 to 1.5 in. W.C. (0 to 375 Pa) differential pressure transmitter supplied with the M9106-AGS-
2N02 and may be ordered separately
DMPR-KC003 Blade Pin Extension without Bracket supplied with Johnson Controls® CD-1300 dampers and
may be ordered separately
DMPR-KR003 Sleeve Pin Kit supplied with Johnson Controls round dampers that have a 5/16 in. (8 mm)
shaft and may be ordered separately
DMPR-KC010* Adjustable Blade Position Indicator Switch Kit with total switching load limited to 2000 VA for
the following applications: Pilot Duty: 24 VAC, 50 VA; 125/250/277 VAC, 125 VA;
Motor Load: 125/250/277 VAC, 1/3 hp; Resistive Load: 125 VAC, 11 A; 250 VAC, 8 A;
277 VAC, 7 A (all maximum values)
* Use with an M9106 actuator to replace an EDA-2040 or ATP-2040 actuator and EDA-2040-102 switch kit.
Dimensions
4.0
See Figure 2 for the actuator and differential pressure 101.6 1.7
transmitter dimensions. 43.2
1.25
31.8
4.33 LO 5.95
(-)
110.0 O
G UT
151.2
N
IN D
DPT
-2
01
5
CCW
COMCW
0.26
6.6 2.05
2.0 52.1
50.8 4.2 0.1
107.3 2.54
1.00
25.4
2.15 2.32
54.6 1.1 58.9
28.3
Note: All dimensions are nominal unless otherwise specified.
Figure 2: M9106-AGS-2N02, in. (mm)
M9106-AGx-2N0x Series Electric Non-spring Return Actuators Submittal Bulletin 3
Technical Specifications
Product M9106-AGx-2N0x Series Electric Non-spring Return Actuators
Power Requirements M9106-AGA-2N01: 24 VAC (20 to 30 VAC) at 50/60 Hz, 2.5 VA supply, Class 2
M9106-AGx-2N02: 24 VAC (20 to 30 VAC) at 50/60 Hz, 2.1 VA supply, Class 2
DPT-2015: 15 VDC (14.5 to 17 VDC) unregulated; 15 mA maximum
Input Signal M9106-AGx-2N0x: 24 VAC (20 to 30 VAC) at 50/60 Hz
Motor Input Impedance M9106-AGA-2N01: 200 ohms, nominal
M9106-AGx-2N02: 250 ohms, nominal
DPT-2015-0 Pressure Range: 0 to 1.5 in. W.C. (0 to 374 Pa)
Over Pressure Limit: 15 in. W.C. (3.74 kPa)
Output Voltage: 0.5 to 4.5 VDC with 25,000 ohm minimum load impedance
Mechanical Output Running Torque: 53 lb∙in (6 N∙m)
Cycles 100,000 full cycles; 2,500,000 repositions rated at 53 lb∙in (6 N∙m)
Audible Noise Rating 35 dBA maximum at 1 m
Rotation Range Adjustable from 30 to 90°, CW or CCW
Rotation Time M9106-AGA-2N01: Nominal 60 seconds at 60 Hz and 72 seconds at 50 Hz for 90°
M9106-AGx-2N02: Nominal 120 seconds at 60 Hz and 144 seconds at 50 Hz for 90°
Electrical Connection No. 6-32 screw terminals on the M9106 actuator; 1/4 in. spade terminals on the DPT-2015
Pressure Connection 6 in. (152 mm) length of silicone tubing with barbed fittings for 1/4 in. (6.35 mm) O.D. tubing
Enclosure NEMA1, IP30
Ambient Operating M9106-AGA-2N0x: 32 to 125°F (0 to 52°C); 90% RH maximum, noncondensing
Conditions M9106-AGS-2N02: 32 to 125°F (0 to 52°C); 90% RH maximum, noncondensing
60 to 100°F (16 to 38°C); 90% RH maximum, noncondensing for
DPT rated accuracy; See DPT-2015 Differential Pressure
Transmitter for VAV Box Applications Installation Instructions
(Part No. 24-7547-18).
Ambient Storage -20 to 150°F (-29 to 66°C); 90% RH maximum, noncondensing
Conditions
Dimensions (H x W x D) M9106-AGA-2N01: 5.95 x 4.2 x 2.15 in. (151.2 x 107.3 x 54.6 mm) M9106-AGx-2N02:
5.95 x 4.2 x 2.32 in. (151.2 x 107.3 x 58.9 mm) with the DPT-2015
Shipping Weight M9106-AGA-2N0x: 2.0 lb (0.91 kg)
M9106-AGS-2N02: 2.2 lb (0.99 kg) with the DPT-2015
Agency Compliance UL Listed, File E27734, CCN XAPX
(M9106 Actuator) CSA Certified, File LR85083, Class 3221 02
CE Mark, EMC Directive 89/336/EEC
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or
misuse of its products.
Controls Group
507 E. Michigan Street
P.O. Box 423 Published in U.S.A.
Milwaukee, WI 53201 www.johnsoncontrols.com
4 M9106-AGx-2N0x Series Electric Non-spring Return Actuators Submittal BulletinПозиції каталогу з цим документом
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.