| Вид документа | Технічний документ |
|---|---|
| Виробник | JCI |
| Код документа | Variable-Speed-Drives |
| Сторінок | 48 |
| Мова документа | англійська |
| Розмір файлу | 0.4 МБ |
Текст документа
Variable Speed Drives Series III
Quick Start Guide
Effective April 2018
New Information
CONTENTS
Step 1—Variable Speed Drives Series III Overview . . . . 1
Step 2—Keypad Operation Overview . . . . . . . . . . . . . . . 3
Step 3—Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 4—Startup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Step 5—Standard Parameter List . . . . . . . . . . . . . . . . . . 10
Appendix A—Fault and Warning Codes . . . . . . . . . . . . . 40
Step 1—Variable Speed Drives Series III Overview
Step 1—Variable Speed Drives Series III Overview
This chapter describes the purpose and contents of this Real Time Clock Battery Activation
manual, the receiving inspection recommendations and
the variable frequency drive catalog numbering system. To activate the real time clock (RTC) functionality in the
VFD, the RTC battery (already mounted in the drive) must
be connected to the control board.
How to Use this Manual Simply remove the primary drive cover, locate the RTC
battery directly below the keypad, and connect the white
The purpose of this manual is to provide you with information 2-wire connector to the receptacle on the control board.
necessary to install, set and customize parameters, start up,
troubleshoot and maintain the variable frequency drive (VFD). Figure 1. RTC Battery Connection
To provide for safe installation and operation of the
equipment, read the safety guidelines at the beginning of this
manual and follow the procedures outlined in the following
chapters before connecting power to the VFD. Keep this
operating manual handy and distribute to all users,
technicians and maintenance personnel for reference.
Receiving and Inspection
The Variable Speed Drives Series III has met a stringent
series of factory quality requirements before shipment. It is
possible that packaging or equipment damage may have
occurred during shipment. After receiving your VFD, please
check for the following:
Check to make sure that the package includes the Instruction
Leaflet, Quick Start Guide, and accessory packet. The
accessory packet includes:
● Rubber grommets
● Control cable grounding clamps
● Additional grounding screw
Inspect the unit to ensure it was not damaged during
shipment.
Make sure that the part number indicated on the nameplate
corresponds with the catalog number on your order. Table 1. Common Abbreviations
If shipping damage has occurred, please contact and file a Abbreviation Definition
claim with the carrier involved immediately. CT Constant torque with high overload rating (150%)
If the delivery does not correspond to your order, please VT Variable torque with low overload rating (110%)
contact your sales representative.
IH High Overload (150%)
Note: Do not destroy the packing. The template printed on IL Low Overload (110%)
the protective cardboard can be used for marking the
mounting points of the VFD on the wall or in a cabinet. VFD Variable Frequency Drive
Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com 1
Step 1—Variable Speed Drives Series III Overview
Rating Label Keypad Overview
Figure 2. Rating Label Figure 3. Keypad and Display
Programmable Programmable
Soft Key 1 Soft Key 2
Increase
Value Scroll Change Control
Menu Up Place to Auto
Back/Reset Move Cursor
Button Right
Start/Hand Button
Stop/Off Button
Move Cursor Decrease Value
Left Scroll Menu Down
Enter Menu
Confirm Selection
Carton Labels (U.S. and Europe)
Same as rating label shown above.
2 Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com
Step 2—Keypad Operation Overview
Step 2—Keypad Operation Overview
The keypad is the interface between the drive and the user.
It features an LCD display, 3 LED lights and 11 buttons. With
the control keypad, it is possible to control the speed of a
motor, to supervise the state of the equipment and to set the
frequency converter’s parameters. See Figure 3.
Keypad Buttons
Buttons Description
Table 2. Keypad Buttons
Icon Button Description
Soft Key 1, Soft Key 1, Soft Key 2:
Soft Key 2 The functions of these two buttons shall be the following:
Forward/Reverse, this shall change motor’s run direction.
Reset, this shall ask MCU to reset after some parameters are modified.
• Menu, this shall return to main menu.
• Details, this shall display the details of the fault.
• Bypass, this shall make drive go into bypass.
• Jog, this shall activate jog.
• Favorite, this shall add this parameter to the Favorite menu.
• Delete, this shall delete this parameter from the Favorite menu.
Back/Reset Back/Reset:
This button has three integrated functions. The button operates as backward button during
normal mode.
In edit mode, it is used as cancel operate. It is also used to reset faults when faults occur.
• Backs up one step.
• Cancels Modify in edit mode.
• Resets the active faults (all the active faults shall be reset by pressing this button
more than 2s in any page).
Auto Auto:
This button switches the drive into the auto control place.
Up Up and Down Arrows:
Down • Move either up or down a menu list to select the desired menu item.
• Editing a parameter bit by bit, while the active digit is scrolled.
• Increase/decrease the reference value of the selected parameter.
• In parameter comparison mode, scroll through the parameters of which current value
is different from comparison parameter value.
• In parameter page when in read mode, move to the previous or next brother
parameter of this parameter.
Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com 3
Step 2—Keypad Operation Overview
Table 2. Keypad Buttons, continued
Icon Button Description
Left Left Arrow:
• Navigation button, movement to left when editing a parameter digit by digit.
• Backs up one step.
Right Right Arrow:
• Enter parameter group mode.
• Enter parameter mode from group mode.
• Enter parameter whole edit mode when this parameter can be written.
• Enter parameter bit by bit edit mode from whole edit mode.
• Navigation button, movement to right when editing a parameter bit by bit.
OK OK:
• To clear all the Fault History if pressed for more than 5s (including 5s) in any page.
• This button is used in the parameter edit mode to save the parameter setting.
• To confirm the start-up list at the end of the Start-Up Wizard.
• To confirm the comparison item in parameters comparison mode.
The following is the same with Right key:
• Enter parameter whole edit mode when this parameter can be written.
• Enter parameter group mode.
• Enter parameter mode from group mode.
Stop/Off Stop/Off:
This button operates as the motor stop button for normal operation and places the drive in the
off control location. The Default is for this button to always be active. It can be changed in
Parameter P4.1.3 to only when “Keypad” is selected as the control source.
• Motor stop from the keypad.
• Transitions drive into an Off control location preventing start from any control source.
Start/Hand Start/Hand:
This button operates as motor start button for normal operation when the “Keypad” is
selected as the active control source, as well as selects the Hand control place location.
• When Keypad is the reference place after hitting the start button, it will jump directly
to the Keypad Ref Screen.
• Places drive into Hand Control place. Hitting start again if keypad is in the control
location will start the Drive.
4 Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com
Step 2—Keypad Operation Overview
LED Lights The lines definition is as below:
The first line is State line, shows:
Table 3. LED State Indicators ● RUN / STP / NRD / FIM / TFM—If motor is running, the
Indicator Description run state shall display “RUN”, otherwise the state display
“STP”. “RUN” blinks when the stop command is sent but
Run:
the drive is decelerating. “NRD” is displayed if the drive is
Indicates that the VFD is running and controlling the load in not ready or does not have a signal. “FIM” is displayed to
Run Drive or Bypass.
indicate it is in Fire Mode and the drive is in a Run state.
Blinks when a stop command has been given but the drive is “TFM” is displayed when in the Fire Mode Test Mode and
still ramping down.
the drive is in a Run State.
Fault:
Turn on when there is one or more active drive fault(s).
● FWD / REV / JOG—If the motor running the direction is
Fault clockwise, it displays “FWD”, otherwise displays “REV”
for counter clockwise. If “Jog” is displayed, it indicates
Hand/OFF/Auto: Jog mode is active.
Hand: If the Hand or Off control place is selected,
Auto turn off the light. ● KEY / I/O / BPS / RBP / BUS / OFF—If it is in bypass
Auto: If the Auto control place is selected, turn on the light. currently, display “BPS”; when run command is given, it
will go to “RBP”; otherwise, if the current control source
is I/O terminal, display “I/O”. If it is keypad, then display
“KEY”; otherwise display “BUS.” When indicates “OFF”, it
LCD Display indicates the drive will not accept a command from the
The keypad LCD indicates the status of the motor and the Hand or Auto Control place.
drive and any faults in motor or drive functions. On the LCD, ● PAR / MON / FLT / OPE / QSW / FAV / TPM / BUx—
the user sees information about the current location in the If the current page is parameter menu, display “PAR”;
menu structure and the item displayed. If monitor menu, then display “MON”; If fault menu, then
display “FLT”; If operation menu, then display “OPE”;
If quick start wizard, then display “QSW”; If optional card
Overview
menu, then display “BOA”; If favorite menu, then display
Five lines shall be displayed in the screen. General view is as “FAV”; If main menu, then display “TPM”. “BUx” indicates
following in Figure 4. the drive being a backup drive when in the redundant drive
system.
Figure 4. General View of LCD
The second line is Code line, which shows the menu code.
Direction Status Menu Location
The third line is Name line, which shows the menu name or
Drive Status Control Place
parameters name.
The fourth line is Value line, which shows the submenu
name or parameters value.
The fifth line is Soft key line, the functions of Soft key 1 and
Soft key 2 are changeable, and the real time is in the middle.
Active
Selection
Real Time Clock
(hh:mm)
Soft Key 1 Soft Key 2
Function Label Function Label
Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com 5
Step 3—Menu Navigation
Step 3—Menu Navigation
Menu Structure
Table 4. Keypad Menu
Item Description Item Description
Monitor M1—Basic Fault F1—Active Fault
M2—IO Status F2—History Fault
M3—Optional Boards F3—Fault Log
M4—Energy savings Option Boards B1—Slot A
M5—FB Monitor Menu B2—Slot B
M6—PID Monitor Favorite
M7—Timer/Interval Control Operate Mode O1—Output Frequency
M8—User Defined Output O2—Freq Reference
M9—MWH Monitor O3—Motor Speed
M10—Multi-Monitoring O4—Motor Current
Parameters P1—Basic Parameter O5—Motor Torque
P2—Inputs O6—Motor Power
P3—Outputs O7—Motor Voltage
P4—Drive Control O8—DC-link Voltage
P5—Motor Control O9—Unit Temperature
P6—Protections O10—Motor Temperature
P7—PID Controller 1 R11—Keypad Reference
P8—PID Controller 2 R12—PID1 Keypad Set Point 1
P9—Fire Mode R13—PID1 Keypad Set Point 2
P10—Bypass Startup Wizard S—Startup Wizard
P11—Real Time Clock
P12—Communication
P13—System
Note: Will vary depending on application selected.
6 Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com
Step 3—Menu Navigation
Menu Navigation
This section provides basic instruction on navigating each
section in the menu structure.
Figure 5. Main Menu Navigation
Back/left key Right/OK key
M – Monitor M1 – Basic
UP key M1.1
… Output Frequency
M10 – Multi-Monitoring 0.00 Hz
P – Parameters P1 – Basic Parameters P1.1 – Min Frequency P1.1
… … Min Frequency
Down key
P13 – System P1.16 – Auto 2 Reference 0.00 Hz
F – Fault F1 – Active Fault
F2 – History Fault
F3 – Fault Log
B – Optional Boards
T – Favorite
O – Operate Mode
S – Startup Wizard
Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com 7
Step 4—Startup Wizard
Step 4—Startup Wizard
Startup Wizard Table 5. Startup Wizard Instructions
In the Startup Wizard, you will be prompted for essential Item Description
information needed by the drive so that it can start 1 Startup Wizard Press OK?
controlling your process. In the Wizard, you will need
2 Application 0 = Basic
the following keypad buttons:
1 = PID
Up/Down buttons. 2 = Advanced
Use these to change value. 3 Language 0 = English
1 = ѝ᮷
2 = Deutsch
4 Real Time Clock yy.mm.dd
hh:mm:ss
5 Daylight Saving 0 = Off
1 = EU
2 = US
OK button. 6 Min Frequency Min: 0.00Hz
Max: Max Frequency
Confirm selection with this button, and enter into
next question. 7 Max Frequency Min: Min Frequency
Max: 400.00Hz
8 Motor Nom Current Min: 0.1A
Back/Reset button. Max: 500.0A
If this button was pressed at the first question, 9 Current Limit Min: Ih*1/10
the Startup Wizard will be cancelled. Max: Ih*2
10 Motor Nom Speed Min: Ih*1/10
Max: Ih*2
Once you have connected power to your frequency
converter, and the Startup Wizard is enabled, follow 11 Motor PF Min: 0.30
these instructions to easily set up your drive. Max: 1.0
12 Motor Nom Voltage Min: 180V
Max: 690V
13 Motor Nom Frequency Min: 30.00 Hz
Max: 400.00 Hz
14 Accel Time 1 Min: 0.1 sec
Max:3000.0 sec
15 Decel Time 1 Min: 0.1 sec
Max:3000.0 sec
16 Hand Control Place 0 = Keypad
1 = I/O Terminal Start 1
2 = I/O Terminal Start 2
3 = Fieldbus
8 Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com
Step 4—Startup Wizard
Table 5. Startup Wizard Instructions, continued
Item Description
17 Hand Reference 0 = AI1
1 = AI2
2 = Slot A: AI1
3 = Slot B: AI1
4 = AI1 Joystick
5 = AI2 Joystick
6 = Keypad
7 = Fieldbus
9 = Max Frequency
10 = AI1 + AI2
11 = AI1 –AI2
12 = AI2 –AI1
13 = AI1 * AI2
14 = AI1 or AI2
15 = Min(AI1,AI2)
16 = Max(AI1,AI2)
17 = PID1 Control Output
18 = PID2 Control Output
18 Auto 1 Control Place 0 = I/O Terminal Start 1
1 = Fieldbus
2 = I/O Terminal Start 2
3 = Keypad
19 Auto 1 Control Reference 0 = AI1
1 = AI2
2 = Slot A: AI1
3 = Slot B: AI1
4 = AI1 Joystick
5 = AI2 Joystick
6 = Keypad
7 = Fieldbus
9 = Max Frequency
10 = AI1 + AI2
11 = AI1 –AI2
12 = AI2 –AI1
13 = AI1 * AI2
14 = AI1 or AI2
15 = Min(AI1,AI2)
16 = Max(AI1,AI2)
17 = PID1 Control Output
18 = PID2 Control Output
20 Bypass Enabled 0 = Disabled
1 = Enabled
21 Application Mini-Wizard Press OK?
Now the Startup Wizard is done. It won’t show again when
next power up. If you want to reset it, please set the Startup
Wizard (P13.1.17) or select it from the main menu screen to
enable and cycle the power to the drive.
Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com 9
Step 5—Standard Parameter List
Step 5—Standard Parameter List
Introduction I/O Controls
The Basic Application is designed for preloaded application
sets for use with HVAC specific terminology and functions. “Terminal To Function” (TTF) Programming
It has the patent Active Energy Control algorithm that will
improve your efficiency as well as minimize losses in your The design behind the programming of the digital inputs in
motor throughout the defined speed range. It provides the the DH1 drive is to use “Terminal To Function”
ability for the user to define its Hand and Auto control and programming, which is composed of multiple functions that
reference signals with the standard Off condition as well. get assigned a digital input to that function. The parameters
In addition there is the ability to scale the analog input and in the drive are set up with specific functions and by defining
output signals to be read based off the desired motor the digital input and slot in some cases, depending on which
response. There are also 8 digital inputs, 3 relay outputs, and options are available. For use of the drives control board
1 digital output that can be programmed to allow for control inputs, they will be referred to as DigIN:1 through DigIN:8.
schemes that require the drive to have certain functions. It When additional option cards are used, they will be defined
provides full customization on the motor control sequence as DigIN:X:IOY:Z. The X indicates the slot that the card is
with the ability to be in frequency or speed control mode, and being installed in, which will be either A or B. The IOY
tuning of the V/Hz curve can be selected. Drive/Motor determines the type of card it is, which would be IO1 or IO5.
protections can be customized to defined actions for added The Z indicates which input is being used on that available
user control. Below is a list of other features that are option card.
available in the Basic Application.
Basic Application includes functions: “Function To Terminal” (FTT) Programming
● Bypass control The design behind the programming of the relay outputs and
digital output in the DH1 drive is to use “Function To
● Fire mode Terminal” programming. It is composed of a terminal, be it a
● Pre heat/cold weather mode relay output or a digital output, that is assigned a parameter.
Within that parameter, it has different functions that can be
● Hand/Off/Auto in individual button for easy change of set.
control mode
The parameters of the Standard Application are explained in
● Programmable protections Appendix A of application manual.
● Programmable digital/analog input/output function The explanations are arranged according to the parameter
number. For the DI function, we use Terminal programming
● Programmable start/stop signal logic method to function (TTF), where there is a fixed input that
● Voltage and current limiters gets programmed to a list of functions. This allows for
multiple inputs to be used for different functions. Connecting
● Energy Savings Calculator a certain input with a certain parameter function is done by
● Two independent set of Acceleration/Deceleration ramps give a parameter an appropriate value. The value is formed
by the location of the input, either being on the standard
● Skip frequency control board or an external option board and the slot it is
located in.
● Start source (Local/Remote control function)
● Reference source
● Flying start
● Volts per Hertz control programmable
● Real time clock—RTC time display
● Auto restart on fault to drive or bypass
● Programmable switching frequency
● Multi-preset speeds
● Fan control
● DC brake
10 Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com
Step 5—Standard Parameter List
Force Open/Force Close Selection Option Board digIN Selection
The Force Open Selection would make the selected function This allows Assignment of a hardware digital input on an
always off. Essentially this is a virtual switch that is always option card to a function, this is set in a format of DigIN:
open. The Force Close Selection would make the selected Y:IO1:X where Y is the slot the option card is inserted on the
function always on. Essentially this is a virtual switch that is Main control board and X is the Input on the Board and IO1 is
always closed. These options are assigned to a function if we the type of option board used.
want to force a state without using a hardware input.
The standard options are DigIn: Force Open—indication that Example:
the parameter function is always going to be open, that being If we set Run Enable to DigIN:A:IO5:6 the drive will be
said depending on the logic of the function this could mean enabled when digital input 6 is closed on the IO5 option card
the function is always not active or always active. When the which is inserted in Slot A, and would not be enabled when
selection of a function is DigIN: Force Closed—indication that digital input 6 on the option card is open.
the parameter function is always going to be closed, that
being said again depending on the location of the function
this could mean the function is always active or not active. Timer Channel Selection
Examples of these options would be ID190 Start Signal 1,
when set to “Force Open” and the drive is A Time Channel is a virtual path to link the digital output of a
timer function to a digital input function. To utilize this feature
looking at I/O terminals for control, in this case the drive a timer or interval would need to be assigned to a time
would never start since this Function is always Open. If this channel 1 through 3, and the input function to be controlled
function is set to “Force closed” the drive would always be would need to be assigned to the same time channel.
in a start mode when in that control location.
Example:
Example:
If we set Run Enable to DigIN:TimeChannel1 the drive will be
If we set Run Enable to Force Closed the drive is always enabled when the timer assigned to Time Channel 1 is active
enabled. If we set the same function to Force Open the drive or High, and would not be enabled when the Time Channel is
would never be Enabled. If a Digital input is to be used to inactive or Low.
activate this Run Enable the function should be assigned to
a hardware input (See below for DIGIN Selections).
Table 6. Drive Communication Ports
DIGIN Selection Port Communication
RJ45 Keypad Port
This allows Assignment of a hardware digital input to a
function, this is set in a format of DigIN:X where X is one Upload/Download Parameters USB to RJ45
of the 8 Digital inputs on the Main control board. Remote Mount Keypad Ethernet
Upgrade Drive Firmware USB to RJ45
Example:
RJ45 Ethernet Port
If we set Run Enable to DigIN:6 the drive will be enabled
when digital input 6 (Terminal 8) is closed, and would not Upload/Download Parameters Ethernet
be enabled when digital input 6 (Terminal 8) is open. BACnet/IP Communications Ethernet
Modbus TCP Communications Ethernet
RS-485 Serial Port 1
Upload/Download Parameters
Upgrade Drive Firmware Two-Wire Twisted Pair
Modbus RTU Communications Two-Wire Twisted Pair
BACnet MS/TP Communications Two-Wire Twisted Pair
SA Bus Two-Wire Twisted Pair
Note
1 Shielded wire recommended.
Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com 11
Step 5—Standard Parameter List
Control I/O Configuration
● Run 240 Vac and 24 Vdc control wiring in separate conduit
● Communication wire to be shielded
Table 7. Analog Signals/Galaxy I/O Interface
External Signal Default
Wiring 1 Pin Name Signal Setting Description
1 +10V Ref. Output Voltage — 10 Vdc Supply Source
Res 2 AI1+ 2 Analog Input 1 0–10V Voltage Speed Reference (Programmable to 4 mA to 20 mA)
3 AI1– Analog Input 1 Ground — Analog Input 1 Common (Ground)
4 AI2+ 2 Analog Input 2 4 mA to 20 mA Current Speed Reference (Programmable to 0–10V)
i
5 AI2– Analog Input 2 Ground — Analog Input 2 Common (Ground)
6 GND I/O Signal Ground — I/O Ground for Reference and Control
7 DIN5 Digital Input 5 Preset Speed B0 Sets frequency output to Preset Speed 1
8 DIN6 Digital Input 6 Fire Mode Enables drive into Fire Mode
9 DIN7 Digital Input 7 Bypass Start (TI–) Enables drive into Bypass mode waiting for drive start
10 DIN8 Digital Input 8 Force Auto (TI+) Input forces drive into Auto Control place
11 CMB DI5 to DI8 Common Grounded Allows source input
12 GND I/O Signal Ground — I/O Ground for Reference and Control
13 24V +24 Vdc Output — Control voltage output (100 mA max.)
14 DO1 Digital Output 1 Ready Shows the drive is ready to run
15 24Vo +24 Vdc Output — Control voltage output (100 mA max.)
16 GND I/O Signal Ground — I/O Ground for Reference and Control
17 AO1+ Analog Output 1 Output Frequency Shows Output frequency to motor 0–60 Hz (4 mA to 20 mA)
18 AO2+ Analog Output 2 Motor Current Shows Motor current of motor 0–FLA (4 mA to 20 mA)
19 24Vi +24 Vdc Input — External control voltage input
20 DIN1 Digital Input 1 Run Forward Input starts drive in forward direction (start enable)
21 DIN2 Digital Input 2 Run Reverse Input starts drive in reverse direction (start enable)
22 DIN3 Digital Input 3 External Fault Input causes drive to fault
23 DIN4 Digital Input 4 Fault Reset Input resets active faults
24 CMA DI1 to DI4 Common Grounded Allows source input
25 A/+ RS-485 Signal A — Fieldbus Communication (Modbus, BACnet, SA Bus)
26 B/– RS-485 Signal B — Fieldbus Communication (Modbus, BACnet, SA Bus)
27 R3NO Relay 3 Normally Open Fault Relay output 3 shows VFD is Faulted
28 R1NC Relay 1 Normally Closed Bypass Run Relay output 1 shows VFD is in a bypass run state
29 R1CM Relay 1 Common
30 R1NO Relay 1 Normally Open
31 R3CM Relay 3 Common Fault Relay output 3 shows VFD is Faulted
32 R2NC Relay 2 Normally Closed Run Relay output 2 shows VFD is in a drive run state
33 R2CM Relay 2 Common
34 R2NO Relay 2 Normally Open
Notes
1 The above wiring demonstrates a SINK configuration. It is important that CMA and CMB are wired to ground (as shown by dashed line).
If a SOURCE configuration is desired, wire 24 V to CMA and CMB and close the inputs to ground. When using the +10 V for AI1, it is
important to wire AI1—ground (as shown by dashed line). If using +10 V for AI1 or AI2, terminals 3, 5, and 6 need to be jumpered together.
2 AI1+ and AI2+ support 10K potentiometer.
12 Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com
Step 5—Standard Parameter List
Basic Application—Parameters List
On the next pages you will find the lists of parameters within the respective parameter
groups. The parameter descriptions are given in Appendix A of application manual. The
descriptions are arranged according to the parameter number.
Column explanations:
Code = Location indication on the keypad; shows the operator the present parameter number
Parameter = Name of parameter
Min = Minimum value of parameter
Max = Maximum value of parameter
Unit = Unit of parameter value; given if available
Default = Value preset by factory
ID = ID number of the parameter
Monitor
Table 8. Basic—M1
Code Parameter Min. Max. Unit Default ID Note
M1.1 Output Frequency Hz 1
M1.2 Freq Reference Hz 24
M1.3 Motor Speed rpm 2
M1.4 Motor Current A 3
M1.5 Motor Torque % 4
M1.6 Motor Power % 5
M1.7 Motor Voltage V 6
M1.8 DC-link Voltage V 7
M1.9 Unit Temperature °C 8
M1.10 Motor Temperature % 9
M1.11 Latest Fault Code 28
M1.12 Instant Motor Power kW 1686
M1.13 RTC Battery Status 583 0 = Not Installed
1 = Installed
2 = Change Battery
3 = OverVoltage
Notes 3 Input function is Level sensed.
1 Parameter value can only be changed after the drive has stopped. 4 Input function is Edge sensed.
2 Parameter value will be set to be default when changing macros. 5 Input function is Edge sensed when using StartP/StopP start logic.
Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com 13
Step 5—Standard Parameter List
Table 9. IO Status—M2
Code Parameter Min. Max. Unit Default ID Note
M2.1 Analog Input 1 Varies 10
M2.2 Analog Input 2 Varies 11
M2.3 Analog Output 1 Varies 25
M2.4 Analog Output 2 Varies 575
M2.5 DI1, DI2, DI3 12
M2.6 DI4, DI5, DI6 13
M2.7 DI7, DI8 576
M2.8 DO1,Virtual RO1,Virtual RO2 14
M2.9 RO1, RO2, RO3 557
Table 10. Optional Boards—M3
Code Parameter Min. Max. Unit Default ID Note
M3.1 PT100 Temperature °C 1000.0 27
Table 11. Energy Savings—M4
Code Parameter Min. Max. Unit Default ID Note
M4.1 2 Energy Savings Varies 0.000 2120
Table 12. FB Monitor Menu—M5
Code Parameter Min. Max. Unit Default ID Note
M5.1 Control Board DIDO Status 2209 Bit 0 = DIN1 Status
Bit 1 = DIN2 Status
Bit 2 = DIN3 Status
Bit 3 = DIN4 Status
Bit 4 = DIN5 Status
Bit 5 = DIN6 Status
Bit 6 = DIN7 Status
Bit 7 = DIN8 Status
Bit 8 = DO1 Status
Bit 9 = RO1 Status
Bit 10 = RO2 Status
Bit 11 = RO3 Status
Bit 12 = Slot A with Board
Bit 13 = Slot B with Board
Bit 14–15 = Not used
Notes 3 Input function is Level sensed.
1 Parameter value can only be changed after the drive has stopped. 4 Input function is Edge sensed.
2 Parameter value will be set to be default when changing macros. 5 Input function is Edge sensed when using StartP/StopP start logic.
14 Variable Speed Drives Series III LIT-12012996—April 2018 www.johnsoncontrols.com
Step 5—Standard Parameter List
Table 11. FB Monitor Menu—M5, continued
Code Parameter Min. Max. Unit Default ID Note
M5.2 SlotA DIDO Status 2210 Bit 0 = IO1_DIN1 Status
Bit 1 = IO1_DIN2 Status
Bit 2 = IO1_DIN3 Status
Bit 3 = IO1_DO1 Status
Bit 4 = IO1_DO2 Status
Bit 5 = IO1_DO3 Status
Bite 6 = IO3_RO1 Status
Bit 7 = IO3_RO2 Status
Bit 8 = IO3_RO3 Status
Bit 9 = IO5_AC1 Status
Bit 10 = IO5_AC2 Status
Bit 11 = IO5_AC3 Status
Bit 12 = IO5_AC4 Status
Bit 13 = IO5_AC5 Status
Bit 14 = IO5_AC6 Status
Bit 15 = Not Used
M5.3 SlotB DIDO Status 2211 Bit 0 = IO1_DIN1 Status
Bit 1 = IO1_DIN2 Status
Bit 2 = IO1_DIN3 Status
Bit 3 = IO1_DO1 Status
Bit 4 = IO1_DO2 Status
Bit 5 = IO1_DO3 Status
Bite 6 = IO3_RO1 Status
Bit 7 = IO3_RO2 Status
Bit 8 = IO3_RO3 Status
Bit 9 = IO5_AC1 Status
Bit 10 = IO5_AC2 Status
Bit 11 = IO5_AC3 Status
Bit 12 = IO5_AC4 Status
Bit 13 = IO5_AC5 Status
Bit 14 = IO5_AC6 Status
Bit 15 = Not Used
M5.4 Application Status Word 29 Bit 0 = MC Ready
Bit 1 = MC_Run
Bit 2 = MC_Fault
Bit 3 = FB_Ref_Active
Bit 4 = MC_Stopping
Bit 5 = MC_Reverse
Bit 6 Показано початок документа. Повний текст — у PDF за посиланням вище.
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.