TE-6300P Series Wall Mount Temperature Sensors Installation Guide

Текст документа

24- 4034- 204, Rev. C
                                                                   Installation Instructions   TE-6300P Wall Mount
                                                                                 Issue Date    March 2016

         TE-6300P Series Wall Mount Temperature Sensors

Applications
North American Emissions Compliance                      Dimensions

 IMPORTANT:            The TE-6300P Series Wall
 Mount Temperature Sensor is intended to provide an
 input to equipment under normal operating
 conditions. Where failure or malfunction of the

                                                                                                           TE-6300P ii01.cdr
 sensor could lead to personal injury or property
 damage to the controlled equipment or other
 property, additional precautions must be designed
 into the control system. Incorporate and maintain
 other devices, such as supervisory or alarm systems
 or safety or limit controls, intended to warn of or            Figure 1: Sensor Dimensions, in. (mm)
 protect against failure or malfunction of the sensor.
                                                         Accessories
 IMPORTANT:            Le TE-6300P Series Wall Mount     To mount the TE-6300P Series Wall Mount Sensor to
 Temperature Sensor est destiné à transmettre des        an electrical box, order the TE-1800-9600 Mounting
 données entrantes à un équipement dans des              Hardware. To order a different cover for the wall mount
 conditions normales de fonctionnement. Lorsqu'une       sensor, refer to the TE-6300 Series Temperature
 défaillance ou un dysfonctionnement du sensor           Sensors Product Bulletin (LIT-216320).
 risque de provoquer des blessures ou
 d'endommager l'équipement contrôlé ou un autre          Mounting
 équipement, la conception du système de contrôle
 doit intégrer des dispositifs de protection             Location Considerations
 supplémentaires. Veiller dans ce cas à intégrer de      Consider the following mounting location guidelines:
 façon permanente d'autres dispositifs, tels que des     •   Avoid areas subject to excessive vibration,
 systèmes de supervision ou d'alarme, ou des                 electrical noise, direct sunlight, or the effects of
 dispositifs de sécurité ou de limitation, ayant une         radiant heat.
 fonction d'avertissement ou de protection en cas de
 défaillance ou de dysfonctionnement du sensor.          •   Keep electrical wiring as short as possible to
                                                             minimize temperature error.
                                                         Mounting the Temperature Sensor
                                                         See Figure 2 and mount the temperature sensor as
Installation                                             follows:
 IMPORTANT:          Do not install the TE-6300P         1. Loosen the socket-head screws on each side of
 Series Wall Mount Temperature Sensor in ambient            the unit with a 0.62 in. hex key and remove the
 temperatures beyond the specified -50 to 122°F             cover.
 (-46 to 50°C) temperature range. Installing the         2. Drill the optional 5/16 in. (8 mm) hole only if using
 temperature sensor in ambient temperatures beyond          the drywall anchors provided; then insert the
 this range may damage the unit and void the                anchors into the holes.
 warranty.
                                                         3. Mount the base plate to the wall using the screws
                                                            provided.
                                                         4. Wire the sensor to the controller wire with the wire
                                                            nuts provided.

© 2016 Johnson Controls, Inc.                                                                                                  1
  Part No. 24-4034-204, Rev. C                                                                  www.johnsoncontrols.com
5. Reposition the cover and tighten the retention screws.
6. Install the optional faceplate (vertical mount only).                       Table 1: Lead Wiring (22 AWG, 6 in.) Color Code
                                                                                Sensor Type                   Lead Color
                                                                                1k ohm Nickel                 White
                                                                                1k ohm Platinum               White with blue stripe
                                                                                2.2k ohm Thermistor           Red

                                                                                  !
                                                           TE-6300P ii02.cdr
                                                                                        CAUTION: Risk of Property Damage.
                                                                               Do not apply power to the system before checking
                                                                               all wiring connections. Short circuited or improperly
                                                                               connected wires may result in permanent damage to
     Figure 2: Installing the Wall Mount Sensor                                the equipment.

Wiring                                                                         MISE EN GARDE: Risque de dégâts matériels.
For 1k ohm nickel temperature sensors, wire                                    Ne pas mettre le système sous tension avant d'avoir
resistance can cause approximately 1F° (0.56C°) of                             vérifié tous les raccords de câblage. Des fils formant
error for every 250 ft (76 m) run of 18 AWG wire, or                           un court-circuit ou connectés de façon incorrecte
every 100 ft (31 m) run of 22 AWG wire. For 1k ohm                             risquent d'endommager irrémédiablement
platinum temperature sensors, can cause                                        l'équipement.
approximately 1F° (0.56C°) of error for every 150 ft
(46 m) run of 18 AWG wire, or every 50 ft (15 m) run of
22 AWG wire. To minimize error due to field wiring,
limit the total resistance of all nickel temperature                           IMPORTANT:         Make all wiring connections in
sensor wiring to 3 ohms, and all platinum temperature                          accordance with local, national, and regional
sensor wiring to 2 ohms.                                                       regulations.

The 2k ohm thermistor applications permit wiring to be
quite long before wire resistance adds significantly to                        Repair Information
total resistance measured at the controller. As a                              For a replacement device, refer to the TE-6300 Series
general rule, a 150 ft (46 m) two-wire 18 AWG run                              Temperature Sensors Product Bulletin (LIT-216320) and
contributes 2 ohms of error, or less than 1F° (0.56C°)                         contact the nearest Johnson Controls® representative.
error over the sensor operating temperature range.
See the appropriate controller documentation for
recommended sensor wiring. See Table 1 for an
explanation of the lead wiring color convention.

2   TE-6300P Series Wall Mount Temperature Sensors Installation Instructions
Technical Specifications
  Product                             TE-6300P Series               Wall Mount Temperature Sensors
  Models                              TE-6314P-1:                   Thin-Film Nickel Temperature Sensor
                                      TE-6324P-1:                   Thin-Film Platinum Temperature Sensor
                                      TE-6344P-1:                   NTC Thermistor Temperature Sensor
  Sensor Reference                    Nickel:                       1k ohms at 70°F (21°C)
  Resistance                          Platinum:                     1k ohms at 32°F (0°C)
                                      Thermistor:                   2,252 ohms at 77°F (25°C)
  Sensor Accuracy                     Nickel:                       ±0.34F° at 70°F (±0.19C° at 21°C)
                                      Platinum:                     ±0.73F° at 70°F (±0.41C° at 21°C), DIN Class B
                                      Thermistor:                   ±0.36F° (±0.2C°) in the range: 32 to 158°F (0 to 70°C)
  Sensor Temperature                  Nickel:                       Approximately 3 ohms/F° (5.4 ohms/C°)
  Coefficient                         Platinum:                     Approximately 2 ohms/F° (3.9 ohms/ C°)
                                      Thermistor:                   Nonlinear, Negative Temperature Coefficient (NTC)
  Materials                           Base Plate:                   Galvanized Steel
                                      Cover:                        Rigid Thermoplastic, White
                                      Face Plate:                   Brushed Aluminum
  Operating Conditions                Temperature                   -50 to 122°F (-46 to 50°C)
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or
misuse of its products.

European Single Point of Contact:                NA/SA Single Point of Contact:                   APAC Single Point of Contact:
JOHNSON CONTROLS                                 JOHNSON CONTROLS                                 JOHNSON CONTROLS
WESTENDHOF 3                                     507 E MICHIGAN ST                                C/O CONTROLS PRODUCT
45143 ESSEN                                      MILWAUKEE WI 53202                               MANAGEMENT
GERMANY                                          USA                                              NO. 22 BLOCK D NEW DISTRICT
                                                                                                  WUXI JIANGSU PROVINCE 214142
                                                                                                  CHINA

                                                                                                                     Building Efficiency
                                                                                            507 E. Michigan Street, Milwaukee, WI 53202

                                              Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.
                                     All other marks herein are the marks of their respective owners. © 2016 Johnson Controls, Inc.

                                                TE-6300P Series Wall Mount Temperature Sensors Installation Instructions 3

Позиції каталогу з цим документом

• TE-6314P-1 — Датчик температуры; 1000 OHM, NI

Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.