| Вид документа | Бюлетень виробу |
|---|---|
| Виробник | JCI |
| Код документа | system-350-y350r-power-module |
| Група обладнання | Y350R Power Module for System 350 Control |
| Сторінок | 4 |
| Мова документа | англійська |
| Розмір файлу | 0.1 МБ |
Текст документа
FANs 930, 930.5, 125
Product/Technical Bulletin Y350R
Issue Date 0414
System 350 Y350R Power Module
The Y350R is a rectified Class 2, 24 VAC power
supply module designed specifically for use with
System 350™ Modular Control Systems.
As with all System 350 products, the Y350R is housed
in a compact NEMA 1, high-impact plastic enclosure.
The modular design provides easy, plug-in
connections for quick installation and future
expandability.
Figure 1: Y350R Power Module
Features and Benefits
Modular Design Enables stage, display, and power modules to be
purchased and installed as necessary
Plug-in Connectors and Eliminates wiring between modules and reduces
35 mm DIN Rail Mounting installation costs
Accepts Input Voltages of Reduces inventory by encompassing the primary
120 or 240 VAC, 50/60 Hz voltage requirements
© 2014 Johnson Controls, Inc. 1
Part No. 24-7664-214, Rev. E
Code No. LIT-930090
A pplication
The Y350R Power Module provides the power IMPORTANT: The Y350R Power Module is
necessary to operate all System 350 controls and intended to provide an input to
add-on modules. For system capabilities, see Table 1. equipment under normal
operating conditions. Where
Table 1: Maximum Number of Add-on failure or malfunction of the
Modules when Powered by a Y350R power module could lead to
personal injury or property
Control Display damage to the controlled
Stage Module
Module Module equipment or other property,
A350A additional precautions must be
9 S350A’s or S350C’s 1 D350
A350B designed into the control system.
6 S350A’s or S350C’s with
A350E Incorporate and maintain other
1 S350P
devices, such as supervisory or
4 S350A’s or S350C’s with alarm systems or safety or limit
2 S350P’s controls, intended to warn of or
A350P 4 S350A’s or S350C’s 1 D350 protect against failure or
2 S350A’s or S350C’s with malfunction of the power module.
1 S350P IMPORTANT : Le Y350R Power Module est
A350R 9 S350A’s or S350C’s 2 D350 destiné à transmettre des
A350S 6 S350A’s or S350C’s with données entrantes à un
1 S350P équipement dans des conditions
4 S350A’s or S350C’s with normales de fonctionnement.
2 S350P’s Lorsqu'une défaillance ou un
dysfonctionnement du power
W351A 5 S351’s 1 D351
module risque de provoquer des
W351P 4 S351’s 1 D351 blessures ou d'endommager
P352A 5 S352’s 1 D352 l'équipement contrôlé ou un autre
équipement, la conception du
P352P No additional stages available 1 D352 système de contrôle doit intégrer
R353 5 S353’s No des dispositifs de protection
display supplémentaires. Veiller dans ce
available cas à intégrer de façon
permanente d'autres dispositifs,
tels que des systèmes de
All System 350 add-on modules snap on to a DIN rail supervision ou d'alarme, ou des
and plug into the control and to each other via 5-pin dispositifs de sécurité ou de
connectors. Add-on modules can be arranged in any limitation, ayant une fonction
order and there is no wiring required to interconnect d'avertissement ou de protection
the System 350 components. en cas de défaillance ou de
dysfonctionnement du power
module.
O peration
The Y350R operates from 240 VAC or 120 VAC
power. A 24 VAC, Class 2, step-down transformer
brings the voltage to a level which the System 350
modules will accept. There are no adjustments for the
power module.
2 Y350R Power Module Product/Technical Bulletin
D imensions ! WARNING: Risk of Electric Shock.
3.68 Mounting Slot (4) Disconnect the power supply
0.145 for No. 6 Screws before making electrical
13 connections. Contact with
0.5
components carrying hazardous
voltage can cause electric shock
75 127
5.00 Y350 and may result in severe personal
2.94
injury or death.
AVERTISSEMENT:Risque de décharge électrique.
Débrancher l'alimentation avant de
réaliser tout branchement
40 61 électrique. Tout contact avec des
DIN Rail
1.56 0.42 Mount 2.40 composants conducteurs de
31
tensions dangereuses risque
1.20
d'entraîner une décharge électrique
et de provoquer des blessures
61 graves, voire mortelles.
2.40
21.6
0.85 2. Connect input wiring to the Y350R power module.
22 Strip approximately 3/8 inch from the wire
Conduit
Hole 0.875 insulation, insert the wire under each terminal
screw, and tighten. (See Figure 3.)
Figure 2: Y350R Dimensions, mm/in. Note: If conduit is used when installing System 350
components, be sure to connect the hub to the
conduit before the hub is secured to the
I nstallation and Wiring enclosure.
The Y350R case has provisions for mounting to a
standard 35 mm DIN rail, or can be mounted using the
four key slot mounting holes located in the rear of the Module Module
case. Connector Connector
Mount System 350 modules in any convenient location
using either the DIN rail mounts or the mounting holes
located on the back of the control case. The
components are not position sensitive, but should be
mounted so they can be easily wired and adjusted.
IMPORTANT: All wiring must be installed to
conform to the National Electrical
Code and local regulations.
1. Secure the module to the DIN rail, wall, or panel. 240 VAC COM 120 VAC
Power Input Terminals
Figure 3: Interior of the Y350R Power Module
Y350R Power Module Product/Technical Bulletin 3
C heckout Procedure
Before applying power, make sure installation and 2. Select DC volts on the DVM and verify that the
wiring connections are according to job specifications. voltage is between 16 and 38 VDC. If the DVM
After necessary adjustments and electrical reading is within range, the Y350R is functioning
connections have been made, put the system in properly.
operation and observe at least three complete
Note: Consult the Troubleshooting section of the
operating cycles before leaving the installation.
appropriate control bulletin for a complete
system troubleshooting procedure.
T roubleshooting 3. If the DVM reading is not within the indicated
voltage range, check wiring and correct if
If the control system does not function properly and the
necessary. If the wiring is correct and the reading
Y350R is suspect, proceed as follows:
remains out of range, replace the Y350R.
1. Connect a Digital Voltmeter (DVM) between the
24V (+) and COM (-) terminals located on the
control module’s left-side connector. (Terminal
designations are marked on the control module.)
R epairs and Replacement
Field repairs or calibration must not be made.
Replacement modules are available through the nearest
Johnson Controls representative. (See Table 2.)
O rdering Information
Table 2: Product Available
Item Product Code Description
Power Module Y350R-1C Rectified, Class 2, 24 VAC Power Supply
S pecifications
Product Y350R Power Module
Input Voltage 120/240 VAC, 50/60 Hz
Output Voltage Rectified 24 VAC, 10 VA, Class 2
Material Case and cover: NEMA 1 high-impact plastic
Ambient Temperature Operating: -34 to 66°C (-30 to 150°F)
Shipping: -40 to 85°C (-40 to 185°F)
Ambient Humidity 0 to 95% RH non-condensing
Mounting Wall or DIN rail
Agency Listing UL Guide No. XAPX, File E27734
CUL Guide No. XAPX7, File E27734
CSA Class No. 4813 02, File LR948
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications,
consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products.
Building Efficiency
507 E. Michigan Street, Milwaukee, WI 53202
® Johnson Controls and PENN are registered trademarks of Johnson Controls, Inc. in the
United States of America and/or other countries. All other trademarks used herein are the property
of their respective owners. © Copyright 2014 by Johnson Controls, Inc. All rights reserved.
4 Y350R Power Module Product/Technical BulletinПозиції каталогу з цим документом
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.