| Вид документа | Каталожна сторінка |
|---|
| Виробник | JCI |
|---|
| Моделі | VA-7010-8101, VA-7010-8103 |
|---|
| Група обладнання | valves |
|---|
| Мова документа | англійська |
|---|
| Розмір файлу | 0.3 МБ |
|---|
Про документ
The VA-7010 electric on/off actuator provides two-position (open-closed) control and mounts with a threaded coupling onto VG5000 forged brass valves. A side lever allows manual opening of a 2-way PDTO valve or the normally closed port of a 3-way valve.
Ключові дані
| Supply voltage | 24 ±10% VAC / 230 ±10% VAC (50/60 Hz) |
|---|
| Power consumption | 7 VA |
|---|
| Minimum force | 90 N at minimum power supply and maximum temperature (50°C) |
|---|
| Nominal stroke | 3 mm (max. 5 mm) |
|---|
| Full stroke time "On" | ≈ 10 s |
|---|
| Full stroke time "Off" | ≈ 5 s |
|---|
| Protection | IP40 (EN 60529), NEMA 1 |
|---|
| Ambient operating condition | +2 to +50 °C, non condensing |
|---|
Застосування
- Two-position (open-closed) control with VG5000 series valve bodies:
- VG52x0xC: 2-way Push Down To Close (Normally Open), PDTC
- VG54x0xC: 2-way Push Down To Open (Normally Closed), PDTO
- VG55x0xC: 3-way mixing with built-in Normally Open bypass
- VG58x0xC: 3-way mixing series
Особливості
- Low or line voltage models available — application flexibility
- AC stall type motor — quiet operation
- Manual lever — manual position mode for servicing
- Flat profile design with small side clearance — mounting close to flat surfaces, saves space
- Actuator can be mounted after valve body is installed — simplifies installation in confined spaces
- Actuator can be rotated after mounting — wiring conduit entry in any direction
Технічні дані
| Parameter |
Value |
| Models |
VA-7010-8101, VA-7010-8103 |
| Type of motor |
Synchronous stall |
| Action |
On / Off |
| Supply voltage (50/60 Hz) |
24 ±10% VAC (8101); 230 ±10% VAC (8103) |
| Power consumption |
7 VA |
| Minimum force |
90 N at minimum power supply and maximum temperature (50°C) |
| Nominal stroke |
3 mm (max. 5 mm) |
| Full stroke time "On" |
≈ 10 s |
| Full stroke time "Off" |
≈ 5 s |
| Protection |
IP40 (EN 60529), NEMA 1 |
| Connection to valves |
M28x1.5 for VG5000 series valves |
| Ambient operating condition |
+2 to +50 °C, non condensing |
| Ambient storage condition |
-20 to +65 °C, non condensing |
| Shipping weight |
0.5 Kg |
| Cable length |
1,5 m |
Варіанти замовлення
- VA-7010-8101: supply voltage 24 VAC
- VA-7010-8103: supply voltage 230 VAC
- UL approved models available on request.
Допуски та стандарти
- EMC directive (89/336 EEC): EN 50081-1, EN 50082-1
- LVD directive (73/23/EEC): EN 60335
Позиції каталогу з цим документом
Текст документа
European Electronic Controls Catalogue
Catalogue Section E
Product Bulletin VA-7010
Issue Date 1299
VA-7010
Electric On/Off Actuator
Introduction
The VA-7010 electric on/off actuator provides a
two-position (open-closed) control and can easily
be mounted with a threaded coupling onto VG5000
forged brass valves (see pertinent bulletin).
A lever at the side of the actuator housing can be
used to manually open a 2Way PDTO valve, on the
normally closed port of a 3-way valve.
VA-7010 Actuator with VG5000 3-way (left)
and 2-way (right) valves
Features and Benefits
! Low or Line voltage models available Provides application flexibility
! AC stall type motor Ensures quiet operation
! Manual lever Allows manual position mode for servicing
! Flat profile design with small side clearance Provides mounting close to flat surfaces; saves
space
! Actuator can be mounted after valve body is Simplifies installation in confined spaces; allows
installed application flexibility
! Actuator can be rotated after mounting Provides easier wiring by locating the wiring conduit
entry in any direction
© 1999 Johnson Controls, Inc. E20
Order Nr. DS 10.463 E
2 VA-7010
Ordering data VG55x0xC
Return
VA-7010-810 Supply
3-way + NO ByPass
Supply voltage
1 24 VAC
3 230 VAC VG58x0xC
2
3-way, mixing
UL approved models are available on request.
*) PDTC = Push down to close
PDTO = Push down to open
Actuator combinations
The VA-7010 series electric on/off actuators are Manual Override
specifically designed to be used with the VG5000
valve series. The ordering data for these valve
The VA-7010 actuator features a manual operating
bodies are as follows:
lever (shown in “Dimensions”) for manually
opening 2-way Push Down To Open valves or
" VG5000 series Normally Closed port of 3-way valves. The lever
will not fully close 2-way Push Down To Close
VG52 0 C 2-way Push Down To Close valves or the Normally Opened port of 3-way
(Normally Open) series valves.
VG54 0 C 2-way Push Down To Open
(Normally Closed) series
VG55 0 C 3-way mixing with built-in
Normally Open bypass Mounting instructions
VG58 0 C 3-way mixing series
WARNING
Please refer to the product bulletin “VG5000 Shock Hazard
Forged Brass Valves” for complete ordering
information. When servicing make sure that:
• The electrical supply to the actuator is
switched off to avoid possible damage to the
Operation equipment, personal injury or shock.
• You do not touch or attempt to connect or
When energised, the actuator motor drives a disconnect wires when electric power is on.
sector gear and arm assembly, which pushes
down axially on the valve stem against the force of
Observe the following recommendations when
the return spring.
mounting the actuator:
When the actuator is de-energised, the return
spring in the valve brings back the valve to its • Make sure the actuator is easily accessible for
normal position. (see “valve action summary”) the electrical connections.
• Make sure actuator is free of thermal insulation
V alve Action Summary material.
• Leave at least 20 mm clearance above the
= Stem movement actuator for mounting purposes. (See
Valve Code Valve Type = flow / = no flow “Dimensions”)
To mount the actuator on a VG5000 valve:
VG52x0xC
1. Place the threaded coupling over the valve
2-way NO, PDTC *) stem on the bonnet.
2. Rotate the actuator to desired position and
VG54x0xC
tighten the coupling securely by hand.
2-way NC, PDTO *)
Note: Never use actuator as a mounting lever
E20
VA-7010 3
W irings instructions
WARNING
When wiring the actuator, please follow the
instructions below:
• Before mounting, wiring or adjusting the When servicing make sure that:
actuator, make sure that the power supply
has been disconnected to avoid possible • The electrical supply to the actuator is switched
harm to material or person. off to avoid possible damage to the equipment,
• Make sure that the line power supply is in personal injury or shock.
accordance with the power supply specified • You do not touch or attempt to connect or
on the actuator. disconnect wires when electric power is on.
• All wiring should conform to local codes and • Do not open or repair, contact the nearest
must be carried out by authorised personnel Johnson Controls commercial system wholesaler
only.
W irings diagrams
Yellow/green
230 VAC
N
24 VAC
L
D imensions (in mm)
>25
Cable entry
63
75
19 Cable length 1,5 m
75 65
Manual/Auto lever
E20
4 VA-7010
S pecifications
Models: VA-7010-8101 VA-7010-8103
Type of motor: Synchronous stall
Action: On / Off
Supply voltage (50/60 Hz): 24 ±10% VAC 230 ±10% VAC
Power consumption: 7 VA
Minimum force: 90 N at minimum power supply and maximum temperature (50°C)
Nominal stroke: 3 mm (max. 5 mm)
Full stroke time "On": ≈ 10 s
Full stroke time "Off": ≈ 5 s
Protection: IP40 EN 60529), NEMA 1
Connection to Valves: M28x1.5 for VG5000 series valves
Ambient Operating condition: +2 to +50 °C, non condensing
Ambient Storage condition: -20 to +65 °C, non condensing
Shipping Weight: 0.5 Kg
Compliance: EMC directive (89 / 336 EEC) according to standard
EN 50081-1, EN 50082-1
LVD directive (73 / 23 / EEC) according to standard
EN 60335
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication
or misuse of its products.
Johnson Controls International, Inc.
Headquarters: Milwaukee, WI, USA
European Headquarters: Westendhof 8, 45143 Essen, Germany
European Factories: Lomagna (Italy), Leeuwarden (The Netherlands), Essen (Germany)
Branch Offices: principal European Cities
This document is subject to change without notice Printed in Europe
E20
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.
