| Вид документа | Бюлетень виробу |
|---|---|
| Виробник | JCI |
| Код документа | m9109-series-electric-non-spring-return-actuators-product-bulletin |
| Група обладнання | M9109 |
| Сторінок | 4 |
| Мова документа | англійська |
| Розмір файлу | 0.1 МБ |
Текст документа
Product Bulletin
Issue Date August 1, 2014
PRODUCT BULLETIN
M9109 Series Electric Non-spring Return Actuators
The M9109 Series direct-mount electric actuators
operate on 24 VAC power and are available for use
with floating or proportional controllers. These
non-spring return actuators are easily installed on a
Variable Air Volume (VAV) box and a damper with a
steel shaft up to 1/2 in. (13 mm) in diameter or
3/8 in. (10 mm) square. They may be field mounted to
a VG1000 Series ball valve using the M900-512 Valve
Linkage Kit.
The M9109 models have an 80 lb∙in (9 N∙m) running
torque. They have a nominal 60-second travel time for
90° of rotation at 60 Hz (72 seconds at 50 Hz) with a
load-independent rotation time. The M9109-xGC-2
models are available with integral auxiliary switches to
perform switching functions at any angle within the
selected rotation range. Position feedback is available
Figure 1: M9109 Non-spring Return Actuator
through a 0 (2) to 10 VDC signal on the M9109-GGx-2
models.
Features and Benefits
35 dBA Rating Meets audibility requirements for open ceilings
Synchronous Drive Provides constant rotation time independent of load
Direct-shaft Mount with Single- Simplifies installation and provides three-point shaft
screw Coupler gripping
Magnetic Clutch Provides torque protection for the damper and
actuator
Jumper-selectable Simplifies installation
Rotation Direction
Adjustable Rotation Stops Allow application versatility with 30 to 90° Clockwise
(CW) or Counterclockwise (CCW) rotation
1/2 in. NPT Threaded Conduit Meets electrical code requirements and allows the
Opening use of armored cable
Manual Gear Release Simplifies setup and field adjustments
Output Position Feedback Provides simple, closed-loop control with accurate
position sensing
© 2014 Johnson Controls, Inc. 1
Code No. LIT-120112 www.johnsoncontrols.com
Application
IMPORTANT: This device is not designed or A controller provides a control signal to the actuator
intended to be used in or near environments where depending upon the desired movement of the
explosive vapors or gases could be present or damper blade. This signal causes the motor to rotate
environments where substances corrosive to the in the proper direction and the damper blade to open
device’s internal components could be present. or close.
Note: To avoid excessive wear or drive time on the
The M9109 is used to position balancing, control, motor for the AGx models, use a controller and/or
round, and zone dampers in typical Heating, software that provides a time-out function to remove
Ventilating, and Air Conditioning (HVAC) applications. the signal at the end of rotation (stall). The
The M9109 mounts directly on the duct surface, GGx models have an auto shutoff to avoid excessive
round damper, or small rectangular damper with an wear or drive time on the motor.
anti-rotation bracket and two sheet metal screws The actuator rotates at a nominal rate of 1.5° per
(included). Additional linkages or couplers are not second (90° in 60 seconds) at 60 Hz input. The
required. actuator rotation is field adjustable from 30 to 90°.
Determine the actual rotation time for actuators using
Operation less than 90° rotation and use that value used with the
controller software. For example, 40 seconds is used
IMPORTANT: The M9109 Series actuator is for 60° rotation.
intended to control equipment under normal
operating conditions. Where failure or malfunction of
an M9109 actuator could lead to an abnormal
Dimensions
operating condition that could cause personal injury See Figure 2 for the actuator dimensions.
or damage to the equipment or other property, other
devices (limit or safety controls) or systems (alarm or
supervisory) intended to warn of, or protect against,
failure or malfunction of an M9109 actuator must be
incorporated into and maintained as part of the
control system.
4.0 Maximum Shaft 1.07
101.6 Dimensions 27.2 5.75
0.39 146
10 1.17
29.8
90 0
6 0 30
6.0 Maximum 0 90
152.4 30 60
Shaft
Dimensions Cover
0.39 to 0.50 Removal 1.88
4.3 10 to 12.7 48
109 2.13
54
4.2 Maximum 1.75/44.45
1.7 Clearance
106.5 45
Note: All dimensions are nominal Required for Anti-rotation Bracket
2.68
unless otherwise specified. Cover Removal Dimensions
68
Figure 2: Actuator and Anti-rotation Bracket Dimensions, in. (mm)
2 M9109 Series Electric Non-spring Return Actuators Product Bulletin
Repairs and Replacement
Field repairs must not be made. For a replacement or Table 1: Actuators
an accessory, refer to the Ordering Information
M9109-AGA-2 M9109-AGC-2 M9109-GGA-2 M9109-GGC-2
M9109 Series
section.
Electric Non-spring
Return Actuators
Ordering Information
80 lb·in (9 N·m)
Contact the nearest Johnson Controls representative,
Floating Control
and specify the desired product code number from
Proportional Control
Table 1 or Table 2
Feedback
0 to 10 VDC
2 Auxiliary Switches
Table 2: Accessories
Product Code
Description
Number
DMPR-KC003* Blade Pin Extension without Bracket for Johnson Controls CD-1300 damper direct-mount applications
DMPR-KR003* Sleeve Pin Kit for Johnson Controls round dampers with a 5/16 in. (8 mm) diameter shaft
M9000-105 Pluggable 3-Terminal Block
M9000-106 Pluggable 4-Terminal Block
M9000-160 Replacement anti-rotation bracket for an M9109 actuator
M9000-200 Commissioning Tool provides a control signal to drive on/off, floating, proportional, or resistive actuators.
M9000-512 Valve Linkage Kit for field mounting an M9109 actuator to a 1/2 and 3/4 in. two-way and three-way
VG1000 Series ball valve
* Furnished with the damper and may be ordered separately.
M9109 Series Electric Non-spring Return Actuators Product Bulletin 3
Technical Data
Product M9109 Series Electric Non-spring Return Actuators
Power Requirements AGx: 20 to 30 VAC at 50/60 Hz; 2.5 VA supply, Class 2
GGx: 20 to 30 VAC at 50/60 Hz; 3.2 VA supply, Class 2
Input Signal AGx: 20 to 30 VAC at 50/60 Hz
GGx: 0 to 10 VDC or 0 to 20 mA
Input Signal Adjustments AGx: CW and COM Terminals, CW rotation;
CCW and COM Terminals, CCW rotation
GGx (Voltage Input or Current Input):
Jumper Selectable: 0 (2) to 10 VDC or 0 (4) to 20 mA
Factory Setting: 0 to 10 VDC, CW rotation with signal increase
Action is jumper selectable Direct (CW) or Reverse (CCW) with signal increase.
Input Impedance AGx: 200 ohms, nominal
GGx: Voltage Input, 150,000 ohms; Current Input, 500 ohms
Feedback Signal GGx: 0 to 10 VDC or 2 to 10 VDC for 90° (10 VDC at 1 mA)
Corresponds to input signal span selection.
Auxiliary Switch Rating xGC: Two Single-Pole, Double-Throw (SPDT) switches rated at 24 VAC,
1.5 A inductive, 3.0 A resistive, 35 VA maximum per switch, Class 2
Mechanical Output Running Torque: 80 lb∙in (9 N∙m)
Cycles 100,000 full cycles; 2,500,000 repositions rated at 80 lb∙in (9 N∙m)
Audible Noise Rating 35 dBA maximum at 1 m
Rotation Range Adjustable from 30 to 90° CW or CCW; mechanically limited to 93°
Rotation Time Nominal 60 seconds at 60 Hz and 72 seconds at 50 Hz for 90°
Electrical Connection 1/4 in. spade terminals (To order optional pluggable terminal blocks, see Table 2.)
Mechanical Connection 3/8 to 1/2 in. (10 to 12.7 mm) round steel shaft or 3/8 in. (10 mm) square steel shaft
Enclosure NEMA 2, IP32
Ambient Operating -4 to 125°F (-20 to 52°C); 90% RH maximum, non-condensing
Conditions
Ambient Storage -40 to 176°F (-40 to 80°C); 90% RH maximum, non-condensing
Conditions
Dimensions (H x W x D) 5.9 x 4.2 x 2.64 in. (150.1 x 106.5 x 67 mm)
Shipping Weight 2.4 lb (1.08 kg)
Agency Compliance UL Listed, File E27734, CCN XAPX
CSA Certified, File LR85083, Class 3221 02
CE Mark, EMC Directive 89/336/EEC
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or
misuse of its products.
Building Efficiency
507 E. Michigan Street, Milwaukee, WI 53202
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.
All other marks herein are the marks of their respective owners. © 2014 Johnson Controls, Inc.
4 M9109 Series Electric Non-spring Return Actuators Product BulletinПозиції каталогу з цим документом
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.