| Вид документа | Бюлетень виробу |
|---|---|
| Виробник | JCI |
| Код документа | m9106-agx-2n0x-series-electric-non-spring-return-actuators-product-bulletin |
| Група обладнання | M9106 |
| Сторінок | 4 |
| Мова документа | англійська |
| Розмір файлу | 0.1 МБ |
Текст документа
Product Bulletin M9106
Issue Date September 2017
M9106-AGx-2N0x Series Electric
Non-spring Return Actuators
The M9106-AGA-2N0x synchronous motor-driven
actuators provide floating (3-wire) control and are
easily installed on a Variable Air Volume (VAV) box.
They may also be installed on a small or medium-sized
damper with a round shaft up to 1/2 inch (13 mm) in
diameter or a 3/8 inch (10 mm) square shaft.
These compact, non-spring return actuators have a
53 lb∙in (6 N∙m) running torque in a compact
easy-to-install package. The actuators are available
with either a nominal 60-second travel time at 60 Hz
(72 seconds at 50 Hz) or a nominal 120-second travel
time at 60 Hz (144 seconds at 50 Hz) for 90° of
rotation.
The M9106-AGS-2N02 Actuator/Transmitter combines
an M9106-AGA-2N02 with a prewired DPT-2015
Differential Pressure Transmitter that has a 0 to 1.5 in. Figure 1: M9106-AGS-2N02 Non-spring
W.C. (0 to 374 Pa) differential pressure range. Return Actuator
Features and Benefits
q 35 dBA Rating Meets audible requirements for open ceilings
q Synchronous Drive Provides constant rotation time independent of
load
q Direct Shaft Mount with Simplifies installation and provides 3-point
Single-screw Coupler shaft gripping
q Magnetic Clutch Provides torque protection for the actuator and
damper
q Adjustable Rotation Stops Allow application versatility with 30 to 90°
Clockwise (CW) or Counterclockwise (CCW)
rotation
q Manual Gear Release Simplifies setup and field adjustments
q Screw Terminal Connection Makes wiring easy
© 2017 Johnson Controls 1
Code No. LIT-2681126 www.johnsoncontrols.com
Application
IMPORTANT: This device is not designed or A 24 VAC signal from the controller to the CW or
intended to be used in or near environments where CCW terminal of the actuator causes the motor to
explosive vapors or gases could be present, or rotate in the proper direction, and moves the
environments where substances corrosive to the damper blades open or closed. When the controller
device’s internal components could be present. stops sending the signal, the actuator remains in place.
Note: To avoid excessive wear or drive time on the
The actuators are used to position balancing, control, motor, use a controller and/or software that provides a
round, and zone dampers in typical Heating, time-out function to remove the signal at the end of
Ventilating, and Air Conditioning (HVAC) applications. rotation (stall).
They are also used to position the blades in a
VAV box. The -2N01 model rotates at a nominal rate of 1.5° per
second (90° in 1 minute). The -2N02 models rotate at
The actuators mount directly to the surface of a a nominal rate of 0.75° per second (90° in 2 minutes).
VAV box, round damper, or small rectangular damper Rotation is field adjustable from 30 to 90°. Actual
with a single No. 10 self-drilling sheet metal screw rotation time for actuators using less than 90° rotation
(included). There are no additional linkages or couplers must be determined, and that value must be used with
required. Clearly labeled electrical terminals simplify the controller software. For example, the travel time for
installation. Refer to the damper or VAV box 60° rotation is 40 seconds for the -2N01 model and
manufacturer’s information to select the proper timing 80 seconds for a -2N02.
for the actuator.
The M9106-AGS-2N02 is prewired with the 20 in.
Note: The damper rotation time must be defined at (0.5 m) CBL-2000-1 Wiring Harness and the
the controller, and the damper point definition must DPT-2015, which is connected to the airflow pickup
match the rotation time of the actuator. device of the VAV box. The DPT-2015 measures
differential pressure and generates a proportional
Operation 0.5 to 4.5 VDC signal. The voltage signal from the
DPT-2015 is read by the VAV controller and converted
IMPORTANT: The M9106-AGx-2N0x Series to airflow in cubic feet per minute (cfm). The wiring
actuator is intended to control equipment under harness is used to connect the transmitter and
normal operating conditions. Where failure or actuator to the VAV Series controller for simplified
malfunction of an M9106-AGx-2N0x actuator could installation.
lead to an abnormal operating condition that could
cause personal injury or damage to the equipment or Only zero calibration is required, which is performed
other property, other devices (limit or safety within the controller. The VAV controller must be
controls), or systems (alarm or supervisory) intended provided with the correct “K” factor and VAV box size
to warn of, or protect against, failure or malfunction to perform the calculations. Refer to the HVAC PRO™
of an M9106-AGx-2N0x actuator must be User's Guide, Appendix B: VAV Controller Flow
incorporated into and maintained as part of the Calculation Constants (LIT-6375185).
control system. M9106-AGx-2N0x models are replacements for the
one- and two-minute EDA-2040 and ATP-2040
When combined with a VAV controller, the actuator actuators. To replace the EDA-2040 or ATP-2040
provides reliable, integrated damper control. See the originally supplied with an EDA-2040-102 switch kit,
M9106-AGx-2N0x Series Electric Non-spring Return use either an:
Actuators Application Note, (LIT-2681116) for various
configurations with and without the DPT-2015 • M9106-AGx-2N0x actuator with the DMPR-KC010
differential pressure transmitter. switch kit (See Table 2.) or
• M9106-AGC-2 actuator: see the M9106-xGx-2
Series Electric Non-spring Return Actuators
Product Bulletin (LIT-2681123) and M9106-xGx-2
Series Electric Non-spring Return Actuators
Installation Instructions (Part No. 34-636-1085) for
more information.
2 M9106-AGx-2N0x Series Electric Non-spring Return Actuators Product Bulletin
Dimensions Repairs and Replacement
See Figure 2 for the actuator and differential pressure Field repairs must not be made. For a replacement or
transmitter dimensions. an accessory, refer to the Ordering Information
4.0
section.
101.6 1.7
43.2
1.25 Ordering Information
31.8 Contact the nearest Johnson Controls representative,
and specify the desired product code number from
Table 1 or 2.
4.33 LO 5.95
110.0 O
(-)
151.2
Table 1: Actuators
G UT
N
IN D
DPT
Product Code Description
-2
01
5 Number
CCW
COMCW M9106-AGA-2N01 Electric actuator
(1-minute rotation time)
0.26 M9106-AGA-2N02 Electric actuator
6.6 2.05
2.0 52.1 (2-minute rotation time)
50.8 4.2 0.1 M9106-AGS-2N02 Electric actuator (2-minute rotation
107.3 2.54
time) includes the DPT-2015 and
CBL-2000-1
1.00
25.4
2.15 2.32
54.6 1.1 58.9
28.3
Note: All dimensions are nominal unless otherwise specified.
Figure 2: M9106-AGS-2N02, in. (mm)
Table 2: Accessories
Product Code Description
Number
CBL-2000-1 20 in. (0.5 m) wiring harness, Underwriters Laboratories, Inc.® (UL) accepted for plenum use,
supplied with the M9106-AGS-2N02 and may be ordered separately; connects the M9106 and
DPT-2015 to the VAV controller
CBL-2000-2 20 in. (0.5 m) plenum-rated wiring harness
CBL-2000-3 72 in. (1.8 m) plenum-rated wiring harness
DPT-2015-0 0 to 1.5 in. W.C. (0 to 375 Pa) differential pressure transmitter supplied with the M9106-AGS-2N02
and may be ordered separately
DMPR-KC003 Blade Pin Extension without Bracket supplied with Johnson Controls® CD-1300 dampers and may
be ordered separately for all direct mount applications
DMPR-KC011 Hex head Blade Pin Extension without Bracket
DMPR-KC012 Hex Head Blade Pin Extension with Bracket
M9106-AGx-2N0x Series Electric Non-spring Return Actuators Product Bulletin 3
Technical Specifications
Product M9106-AGx-2N0x Series Electric Non-spring Return Actuators
Power Requirements M9106-AGA-2N01: 24 VAC (20 to 30 VAC) at 50/60 Hz, 2.5 VA supply, Class 2
M9106-AGx-2N02: 24 VAC (20 to 30 VAC) at 50/60 Hz, 2.1 VA supply, Class 2
DPT-2015: 15 VDC (14.5 to 17 VDC) unregulated; 15 mA maximum
Input Signal M9106-AGx-2N0x: 24 VAC (20 to 30 VAC) at 50/60 Hz
Motor Input Impedance M9106-AGA-2N01: 200 ohms, nominal
M9106-AGx-2N02: 250 ohms, nominal
DPT-2015-0 Pressure Range: 0 to 1.5 in. W.C. (0 to 374 Pa)
Over Pressure Limit: 15 in. W.C. (3.74 kPa)
Output Voltage: 0.5 to 4.5 VDC with 25,000 ohm minimum load impedance
Mechanical Output Running Torque: 53 lb∙in (6 N∙m)
Cycles 100,000 full cycles; 2,500,000 repositions rated at 53 lb∙in (6 N∙m)
Audible Noise Rating 35 dBA maximum at 1 m
Rotation Range Adjustable from 30 to 90°, CW or CCW
Rotation Time M9106-AGA-2N01: Nominal 60 seconds at 60 Hz and 72 seconds at 50 Hz for 90°
M9106-AGx-2N02: Nominal 120 seconds at 60 Hz and 144 seconds at 50 Hz for 90°
Electrical Connection No. 6-32 screw terminals on the M9106 actuator; 1/4 in. spade terminals on the DPT-2015
Pressure Connection 6 in. (152 mm) length of silicone tubing with barbed fittings for 1/4 in. (6.35 mm)
O.D. tubing
Enclosure NEMA1, IP30
Ambient Operating M9106-AGA-2N0x: 32 to 125°F (0 to 52°C); 90% RH maximum, non-condensing
Conditions M9106-AGS-2N02: 32 to 125°F (0 to 52°C); 90% RH maximum, non-condensing
60 to 100°F (16 to 38°C); 90% RH maximum, non-condensing
For DPT rated accuracy, see DPT-2015 Differential Pressure Transmitter for VAV Box
Applications Installation Instructions (Part No. 24-7547-18.)
Ambient Storage -20 to 150°F (-29 to 66°C); 90% RH maximum, non-condensing
Conditions
Dimensions (H x W x D) M9106-AGA-2N01: 5.95 x 4.2 x 2.15 in. (151.2 x 107.3 x 54.6 mm)
M9106-AGx-2N02: 5.95 x 4.2 x 2.32 in. (151.2 x 107.3 x 58.9 mm) with the
DPT-2015
Shipping Weight M9106-AGA-2N0x: 2.0 lb (0.91 kg)
M9106-AGS-2N02: 2.2 lb (0.99 kg) with the DPT-2015
Agency Compliance UL 873 Listed, File E27734, CCN XAPX
(M9106 Actuator) CSA C22.2 No. 139 Certified, File LR85083, Class 3221 02
CE Mark, EMC Directive 2004/108/EC
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls shall not be liable for damages resulting from misapplication or
misuse of its products.
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls.
All other marks herein are the marks of their respective owners. © 2017 Johnson Controls.
4 M9106-AGx-2N0x Series Electric Non-spring Return Actuators Product BulletinПозиції каталогу з цим документом
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.