| Вид документа | Прикладна нотатка |
|---|---|
| Виробник | JCI |
| Код документа | ln-series-input-output-i-o-extension-modules-and-ln-communicating-sensors |
| Група обладнання | LN Controller |
| Сторінок | 12 |
| Мова документа | англійська |
| Розмір файлу | 0.5 МБ |
Текст документа
LN Series Input/Output (I/O) Extension Modules and LN
Communicating Sensors Subnetwork for
LN-VAVCF-12 and LN-PRGxxx-12 Code No. LIT-12011815
Software Release 6.0
Application Note Issued January 30, 2013
LN-IOE400-0, LN-IOE410-0, LN-IOE420-0, LN-VAVCF-12, LN-PRGxxx-12
Document Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Related Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Subnetwork Bus Total Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Subnetwork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Topology and EOL Terminations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connecting to the LONWORKS Network Through an
LN Communicating Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Enabling the Net to Subnet Port Settings Jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Configuring the LN Communicating Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting to the LON USB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Subnetwork Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Physical Specifications and Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors 1
Subnetwork for LN-VAVCF-12 and LN-PRGxxx-12 Application Note
2 LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN-
VAVCF-12 and LN-PRGxxx-12 Application Note
LN Series Input/Output (I/O) Extension Modules and LN
Communicating Sensors Subnetwork for
LN-VAVCF-12 and LN-PRGxxx-12
Application Note
Document Introduction
This document describes the subnetwork for the LN Series Input/Output Extension
Modules and LN Series Communicating Sensors. The LN-VAVCF0-12 and
LN-PRGxxx-12 Series Controllers are equipped with an RJ-45 subnetwork port to
quickly connect with subnetwork devices such as the LN Communicating Sensors
using a Cat 5e cable (standard patch Ethernet cable). In addition, the
LN-PRG6x0-12 Series controllers can also link to the LN-IOE-4x0 I/O Extension
Modules through the subnetwork. The subnetwork for the LN-IOE-4x0 I/O
Extension Modules uses a standard screw-type terminal block connector and
twisted pair shielded cable.
This document does not describe how to set up a LONWORKS® network. For
information on setting up your LONWORKS® network, refer to the LONWORKS®
LN-Series Network Communication and Interface Guide Technical Bulletin
(LIT-12011253).
Related Documentation
Table 1: Related Documentation
For Information On See Document LIT Number
Setting Up a LONWORKS Network LONWorks LN-Series Network LIT-12011253
Communication and Interface Guide
Technical Bulletin
Setting Up a Subnetwork with LN LN Series Input/Output (I/O) LIT-12011706
Series Input/Output Extension Extension Modules Subnetwork for
Modules Subnetwork for LN-PRG6x0-2 Application Note
LN-PRG6x0-2
Installing LN Free Programmable LN Free Programmable PRG 600 LIT-12011691
PRG 600 Series Controllers Series Controllers Installation
Instructions
Installing LN Series Input/Output LN Series Input/Output (I/O) LIT-12011693
(I/O) Extension Modules Extension Modules Installation
Instructions
LN Free Programmable PRG 600 LN Free Programmable PRG 600 LIT-12011656
Series Controllers and LN I/O and LN Input/Output Extension
Extension Modules Features and Modules Product Bulletin
Benefits
LN Series Communicating Sensors LN Series Communicating Sensors LIT-12011779
Features and Benefits Product Bulletin
LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN- 3
VAVCF-12 and LN-PRGxxx-12 Application Note
Subnetwork Bus Total Length
The total maximum length of all subnetwork buses, including both the length of
the LN Series I/O Extension Modules subnetwork bus and the LN Series
Communicating Sensors subnetwork bus is 300 m (1,000 ft). The maximum length
of the LN Series I/O Extension Modules subnetwork bus is 300 m (1,000 ft)
(Figure 1). The maximum length of the LN Series Communicating Sensors
subnetwork bus is 200 m (650 ft) (Figure 2).
Figure 1: Maximum Length of the LN I/O Extension Modules
Subnetwork Bus
Figure 2: Maximum Length of the LN Communicating Sensors
Subnetwork Bus with an LN-VAVCF-12 Controller
4 LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN-
VAVCF-12 and LN-PRGxxx-12 Application Note
Since the total maximum length of all subnetwork buses cannot exceed
300 m (1,000 ft), the length of one subnetwork bus affects the length of other
subnetwork buses. Figure 3 shows that if the LN Series Communicating Sensors
subnetwork is 150 m (500 ft), then the LN Series I/O Extension Modules
subnetwork length can only be a maximum of 150 m (500 ft).
Figure 3: Example of Distribution and Total Maximum Length of
Subnetwork Bus Length
Subnetwork
Figure 4 shows the LN Series Input/Output Extension modules on the
subnetwork with the proper End-of-Line (EOL) terminations.
Figure 4: EOL Terminations Settings on Subnetwork
Note: In Figure 4, the EOL jumpers are located on the inside of the controller and
modules.
LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN- 5
VAVCF-12 and LN-PRGxxx-12 Application Note
When LN-IOE4x0 modules are installed with an LN-PRG6x0 controller and with
LN Communicating Sensors, only the EOL terminations of the last LN-IOE4x0
and the last LN Communicating Sensor are set to ON. All other LN-IOE4x0
modules and LN Communicating Sensors must have their EOL terminations set to
OFF (Figure 5).
Figure 5: Setting the EOL Terminations on the LN-IOE4x0 Subnetwork
Bus When the LN Communicating Sensors Are Used
Topology and EOL Terminations
Set the EOL terminations on the LN Free Programmable PRG 600 Series
Controller and the last LN I/O Extension Module to ON. All other extension
modules must have their EOL termination set to OFF (Figure 4).
Connecting to the LONWORKS Network Through an
LN Communicating Sensor
The subnetwork bus extends the LONWORKS network to the LN Communicating
Sensors to provide convenient network access for maintenance and
troubleshooting purposes (Figure 6).
6 LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN-
VAVCF-12 and LN-PRGxxx-12 Application Note
This section explains how to enable the LONWORKS network with the LN
Communicating Sensors. A LONWORKS network has a limited number of enabled
controllers.
Figure 6: LN Communicating Sensors Subnetwork with LONWORKS
Network
To provide LONWORKS network access, jumpers on both the controller and the
LN Communicating Sensor must be enabled.
All LONWORKS controllers have Net to Subnet Port Settings jumpers, which
(when enabled) connect the LONWORKS network to the LN Communicating
Sensor.
Note: Only a limited number of controllers on the LONWORKS network segment
should have their Net to Subnet Port Settings jumpers enabled. Enabling
too many LN Communicating Sensors with network access may cause
communication issues.
LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN- 7
VAVCF-12 and LN-PRGxxx-12 Application Note
Figure 7 shows a typical LONWORKS network bus topology with only a few
controllers enabled for network access at the LN Communicating Sensor.
Figure 7: LONWORKS Network Bus Topology
For maximum cable lengths and cable specifications for LONWORKS network bus
topology, see Table 2.
The length of the LN Communicating Sensor subnetwork bus must also comply
with the restrictions shown in Figure 1 and Figure 2.
Enabling the Net to Subnet Port Settings Jumper
To connect the main LONWORKS network to the LN Communicating Sensor
subnetwork Cat5e cable, set the two Net to Subnet Port Settings jumpers inside
the LN-PRG6x0 controller to Enable (Figure 8). The factory default for the Net to
Subnet Port Settings jumpers is set to Disable.
Figure 8: Jumpers Set to Enabled on the LN-PRG6x0 Controller
8 LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN-
VAVCF-12 and LN-PRGxxx-12 Application Note
To connect the main LONWORKS network to the LN Communicating Sensor
subnetwork Cat5e cable, set the two Net to Subnet Port Settings jumpers inside
the LN-VAVCF-12 controller to Enable (Figure 9). The factory default for the Net
to Subnet Port Settings jumpers is set to Disable.
Figure 9: Jumpers Set to Enabled on the LN-VAVCF-12 Controller
Configuring the LN Communicating Sensor
On each LN Communicating Sensor, ensure that the BAC/LON jumper is set to the
LON position (Figure 10). Use this setting for all LN Communicating Sensors, in
case you wish to enable the network in the future.
Figure 10: LN Communicating Sensor BAC/LON
Jumper Set to LON
LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN- 9
VAVCF-12 and LN-PRGxxx-12 Application Note
Connecting to the LON USB Interface
To temporarily access the LONWORKS network for commissioning and
maintenance purposes, connect a LON USB Network Interface to the stereo audio
plug located on the lower edge of the LN Communicating Sensor. You can then
wire a standard 3.5 mm (1/8 in.) three-conductor (stereo jack) or two-conductor
(mono jack) as shown in Figure 11.
Figure 11: Connecting to LONWORKS Network via Stereo Jack on LN
Communicating Sensor
Subnetwork Length
The total maximum length of the subnetwork is 300 meters (1,000 feet). The
polarity of the LN Series I/O Extension Modules must be configured as shown in
Figure 12. All terminals identified as SUBNET+ must be connected to the same
conductor. Similarly, all terminals identified as SUBNET- must be connected to the
same conductor.
Figure 12: LN Free Programmable PRG 600 Series Controllers
Subnetwork Shielding
10 LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN-
VAVCF-12 and LN-PRGxxx-12 Application Note
Use properly grounded, shielded cable for the best protection against interference
on the LN Series I/O Extension Module subnetwork. Use the daisy-chain
configuration with the cable shield twisted together and isolated with electrical
tape at each extension module.
When you use an LN Free Programmable PRG 600 Series Controller, connect the
shielding of the extension modules on the subnetwork to the electrical system
ground at one point only (Figure 12).
Physical Specifications and Cable Requirements
Use cables composed of stranded conductors, instead of solid conductors, for the
best breakage resistance during pulling operations. Table 2 describes the physical
specifications and cable requirements for an LN Series I/O Extension Module
subnetwork.
Table 2: Physical Specifications and Cable Requirements
Specification Description
Maximum Number of LN Series I/O 2 LN Series I/O Extension Modules
Extension Modules
Media Shielded, Twisted Pair
Characteristic Impedance 100–130 ohm
Distributed Capacitance Less than 100 pF per meter (30 pF per foot)
Maximum Length of the LN Series I/O 300 meters (1,000 ft) Maximum
Extension Modules Subnetwork
Polarity Polarity Sensitive
Multi-Drop Daisy-chain (No Routers)
End-of-Line (EOL) Terminations Built-in and set (enabled) on the last extension
module only.
Shield Grounding See Figure 12.
LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN- 11
VAVCF-12 and LN-PRGxxx-12 Application Note
Addressing
Each LN Series I/O Extension Module on the subnetwork must have a unique
address. The current valid addresses are 1 or 2. Figure 13 shows an example of
how to set a DIP switch. Table 3 shows the DIP switch settings.
Figure 13: DIP Switch Set to 2
Table 3: DIP Switch Settings
Switch Position Value
1 2 3
OFF OFF OFF Invalid
ON OFF OFF 1
OFF ON OFF 2
ON ON OFF Invalid
OFF OFF ON Invalid
ON OFF ON Invalid
OFF ON ON Invalid
ON ON ON Invalid
Building Efficiency
507 E. Michigan Street, Milwaukee, WI 53202
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.
All other marks herein are the marks of their respective owners. © 2013 Johnson Controls, Inc.
12 LN Series Input/Output (I/O) Extension Modules and LN Communicating Sensors Subnetwork for LN-
VAVCF-12 and LN-PRGxxx-12 Application Note
Published in U.S.A. www.johnsoncontrols.comПозиції каталогу з цим документом
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.