Файл за старою адресою не зберігся. Нижче — документ виробника на те саме обладнання.
| Вид документа | Каталожна сторінка |
|---|---|
| Виробник | JCI |
| Моделі | VG8300N, VG8300H |
| Група обладнання | valves |
| Мова документа | англійська |
| Розмір файлу | 0.4 МБ |
Про документ
Two-way Push-Down-To-Close (PDTC) nodular iron flanged globe valves for modulating water and steam flow in HVAC systems. The balanced-pressure design (equalisation chamber above the plug) allows higher close-off pressures with standard actuators. VG8300N is rated PN 16 and VG8300H PN 25.
Ключові дані
| body rating | PN 16 (VG8300N), PN 25 (VG8300H) |
|---|---|
| size range | DN 40 - DN 150 |
| kvs range | 25 / 40 / 63 / 100 / 160 / 250 / 350 (per DN 40…150) |
| fluid temperature limits | 2 °C … 180 °C (VG8300N), 2 °C … 200 °C (VG8300H); with optional glycerine cup down to -10 °C / -20 °C |
| max ∆pv100 | 500 kPa with water, 800 kPa heavy duty (VG8300N); 1000 kPa with water, 1600 kPa heavy duty (VG8300H) |
| flow characteristic | Equal percentage |
| practical rangeability (kvs/kvr) | 6001 |
| leakage rate | Max. 0.05 % of kvs DIN 32730; test with water per DIN EN1349 |
| body material | Nodular cast iron EN-GJS-400-15 (EN-JS1030) PN 16; EN-GJS-400-18-LT (EN-JS1025) PN 25 |
Застосування
- Regulating the flow of water and steam in response to a controller demand in heating, ventilating and air conditioning systems
- Water and glycol solutions (max 50 %) or steam; proper water treatment recommended (VDI 2035)
Особливості
- Balanced pressure valve — expensive high thrust actuators no longer necessary
- PN 16 & PN 25 rated bodies within a Johnson Controls flanged valve program covering PN 6, PN 10, PN 16 & PN 25
- Stainless steel stem-plug-welded seat area combination for stability and durability
- Spring loaded, self-adjusting Teflon-Viton-Teflon V-ring packing; no readjustment required
- Low leakage rate (max. 0.05 % of kvs) for maximum energy efficiency
- Slotted stem for Johnson Controls quick-fit coupler system
- Valves are silicon free
- Optional glycerine cup packing for fluid temperatures below 0 °C (imperative below 0 °C)
- Compatible with Johnson Controls pneumatic and electric actuators; equal percentage flow characteristic; flow-direction arrow on body
Технічні дані
| Parameter | Value |
|---|---|
| Models | VG8300N (PN 16), VG8300H (PN 25), 2-way balanced pressure PDTC, DN 40…150 |
| Service | Water, glycol solutions (max 50 %) or steam, HVAC applications |
| DN | 40 / 50 / 65 / 80 / 100 / 125 / 150 |
| kvs per DN | 25 / 40 / 63 / 100 / 160 / 250 / 350 |
| Nominal stroke | 13 mm (DN 40), 25 mm (DN 50–80), 42 mm (DN 100–150) |
| Weight (kg), VG8300N by DN | 12 / 14 / 18.5 / 25.5 / 35.5 / 55 / 75 |
| Fluid temperature limits | VG8300N: 2 °C…180 °C (DN 125 & 150: 2 °C…130 °C); VG8300H: 2 °C…200 °C; below 0 °C optional glycerine cup must be used (-10 °C VG8300N, -20 °C VG8300H) |
| Body material | Nodular cast iron EN-GJS-400-15, Mat. spec. No. EN-JS1030 (PN 16); EN-GJS-400-18-LT, Mat. spec. No. EN-JS1025 (PN 25) |
| Stem / Plug / Seat edge material | Stainless steel, material specification 1.4305 |
| Packing | Teflon-Viton-Teflon V-ring combination, spring loaded, self adjusting; Aramid fibre-Viton-Aramid fibre when glycerine cup is used |
| Face to face dimensions | DIN EN558-1 |
| Flange dimensions | DIN EN1092-2, form B seal strip (pre-welded flange recommended per DIN EN1092-2) |
| Flow characteristic | Equal percentage |
| Practical rangeability (kvs/kvr) | 100:1 |
| Sensitivity ngl (ideal rangeability) | 4.5 for kvs ≥ 1; 3.2 for kvs 0.4…0.63 |
| Max. ∆pv100 | VG8300N: 500 kPa with water, 800 kPa heavy duty model for superheated steam; VG8300H: 1000 kPa with water, 1600 kPa heavy duty model |
| Leakage rate | Max. 0.05 % of kvs DIN 32730; test with water as per DIN EN1349 |
| Valve/actuator combinations | MP-8000 pneumatic (DN 40), PA-2000 pneumatic (DN 40–150), VA-7200 electric (DN 40), RA-3000 electric (DN 40–150), RA-3100 electric fast running, FA-2000 electric spring return (DN 40–150) |
Варіанти замовлення
Ordering code structure: VG83 <size/kvs> S1 <body rating> — e.g. VG83G1S1N = DN 65, kvs 63, PN 16.
Body ordering codes:
| Code | DN | kvs |
|---|---|---|
| E2 | 40 | 16 |
| E1 | 40 | 25 |
| F1 | 50 | 40 |
| G1 | 65 | 63 |
| H1 | 80 | 100 |
| J1 | 100 | 160 |
| K1 | 125 | 250 |
| L1 | 150 | 350 |
- Glycerine cup packing: add suffix "20" (e.g. VG83xxxS1H20)
- Reduced kvs coefficients available on request
- Factory-mounted actuator: add "+M" behind actuator order code
- Replacement packing kits: 121 4393 011 (DN 40), 121 4409 011 (DN 50–80), 121 4433 011 (DN 100–150); glycerine cup kits 121 4434/4435/4436 011 + installation kit 121 44xx 111
- Special models (heavy duty, special coating) available on request; PA-2000 can be specially ordered as Teflon-free model
Actuator highlights:
- MP8000 pneumatic: spring ranges 20…50 kPa, 60…90 kPa, 70…100 kPa; options positioner PY-1010 (D.A.), hand wheel, feedback 2 kΩ + aux. switches
- PA-2000 pneumatic: D.A./R.A., sizes 150 cm² (DN 15–40), 300 cm² (DN 50–80), 600 cm² (DN 100–150); spring ranges C 20…50 kPa, E 60…90 kPa, 7 70…100 kPa
- VA-7200 electric: 24 V or 230 V 50/60 Hz, 1000 N thrust, 13 mm stroke; 3-point or 0…10 VDC proportional; options feedback pot, aux. switches, manual override
- RA-3000 electric: RA-3000-712x 1600 N / 13 mm stroke (~82 s), RA-3000-722x 1800 N / 25 mm stroke (~140 s), RA-3000-732x 3000 N / 42 mm stroke (~185 s); 24 V or 230 V 50/60 Hz
- RA-3100 electric fast running: RA-3100-8126 1200 N / 23.4 s (13 mm), RA-3100-8226 1700 N / ~17.5 s (25 mm) / ~29.4 s (42 mm); 24 V
- FA-2000 electric spring return: FA-2000-711x 2000 N / 13 mm stroke, FA-2xxx-751x 2400 N / 25 mm stroke, FA-2xxx-741x 2200 N / 42 mm stroke; 230 V or 24 V 50 Hz; built-in electronic positioner 0…10 V / 0(4)…20 mA option
Допуски та стандарти
- Pressure Equipment Directive 97/23/EU: pressure accessory module D1 for DN 40…125; modules B & D for DN 150; notified body TÜV Süddeutschland Bau & Betrieb GmbH, ID No. 0036
- Standards: DIN EN60534-1, DIN EN558-1, DIN EN1092-2, DIN EN1349
Текст документа
European Electronic Controls Catalogue
Catalogue Section E
Product Bulletin VG8300N & H
Issue Date 0303
VG8300N & H Series PN 16 & PN 25, DN 40 - DN 150
Balanced Pressure Nodular Iron Flanged Valves
I ntroduction
The VG8300N PN 16 and VG8300H PN 25 valve
series are designed primarily to regulate the flow
of water and steam in response to the demand of
a controller, in heating, ventilating and air
conditioning systems.
These two-way Push-Down-To-Close, nodular
cast iron valves have a specially designed plug,
which through specific balancing of pressures
allows higher close-off pressures with standard
actuator combinations.
The VG8300N and VG8300H valves can be used
with a variety of Johnson Controls pneumatic and
electric actuators.
VG8300N and VG8300H Valves
(With PA and RA Actuators)
Features and Benefits
Balanced pressure valve. Cost saving technology, expensive high thrust
actuators no longer necessary.
PN 16 & PN 25 rated valves available. Johnson Controls flanged valve program covers a
wide range of applications (body ratings PN 6,
PN 10, PN 16, & PN 25).
Nodular iron valve bodies. Compact, lighter and more ductile than ordinary cast
iron (EN-GJS-400-15-LT: PN 16)
(EN-GJS-400-18-LT: PN 25).
Stainless steel stem-plug-welded seat area Provides stability and durability.
combination.
Pneumatic and electric actuators available. Allows optimum choice of actuator.
Use of standard Johnson Controls spring Reliable, field-proven seal applicable to wide
loaded, self-adjusting Teflon-Viton-Teflon operating temperature range. No readjustment
V-ring packing. required.
Low leakage rate. Provides maximum energy efficiency.
Slotted stem for Johnson Controls coupler. Simple and robust quick-fit coupler system reduces
installation costs.
Valves are silicon free. No silicon particles floating free.
© 2000 Johnson Controls, Inc. E18.2
Order No. DS 10.485 E
2 VG8300N & H
A pplication Overview O rdering codes for Valve Bodies
Valve bodies are made of nodular cast iron and Two-Way PDTC
are available in sizes from 40 mm to 150 mm.
Flanged connections comply with EN and DIN VG83 S1
standards. These valves also comply with Body Type
Pressure Equipment Directives (PED). N PN 16
Information regarding the CE mark can be found H PN 25
on the valve ID plate. The valve trim and seat Size kvs
edge are made of stainless steel. The valve
E2 DN 40 16
packing consists of spring loaded Viton-Teflon V-
rings. E1 DN 40 25
F1 DN 50 40
The VG8300N & H Bonnet G1 DN 65 63
Slotted Stem H1 DN 80 100
Spring loaded, self J1 DN 100 160
adjusting packing K1 DN 125 250
L1 DN 150 350
Bonnet For ordering a valve with Glycerine cup packing,
add suffix "20" to the ordering code: i.e.
Body VG8xxxS1H20.
Equalisation chamber Reduced kvs coefficients are available on request
Flow direction a longer delivery time should be taken into
account.
Plug
Ordering Example:
Flow direction
For a DN 65, kvs 63, PN 16 valve, the ordering
code is: VG83G1S1N
The valve design incorporates a pressure
Special models (heavy duty, special coating) are
equalisation chamber above the valve plug. A
available on request.
connection between the chamber and the area
beneath the plug allows fluid pressures on both
sides of the plug to find a balance. This means V alve Selection
The valve size for water applications can be
that with higher close-off pressures, the actuator
required to close the valve need not be of as high defined using the diagrams below, where the
a thrust as would be necessary for a normal valve intersection of the pressure drop across the valve
under similar conditions. and the flow must be within the white area.
The VG8300N and VG8300H valve series are kv selection diagram for DN 40...150
available in two-way PDTC configuration. valves:
These two-way valves have an equal percentage 1000
800
flow characteristic. An arrow is embossed on one 600
side of the valve body indicating the direction of 400
300
flow for correct installation. 200
The upper operating fluid temperature range limit 350
250 100
of the VG8300N is 180°C and 200°C for the
Flow Q, in m3/h
80
VG8300H. 160 60
100 40
Models where packing includes an optional cup 30
63
for glycerine anti-freeze are available for fluid 20
40
temperatures as low as -10°C for the VG8300N 10
25
and -20 °C for the VG8300H. 8
16 6
Note: This option is imperative where 4
temperatures can fall below 0°C 3
A variety of electric actuators are available and
can be ordered as a factory fitted valve/actuator 1
0.8
combination or as a single item for on site 0.6
installation. 0.4
Pressure drop ∆p in kPa (100 kPa = 1 bar)
E18.2
VG8300N & H 3
Valve - Actuator Combinations
The VG8300N and VG8300H series nodular iron • RA-3000 electric actuators (DN 40 ...150)
flanged valves can be combined with the following • FA-2000 electric spring return actuators
series of pneumatic and electric actuators: (DN 40...150)
• MP-8000 pneumatic actuators (DN 40) Please see the relevant product bulletin for more
• PA-2000 pneumatic actuators (DN 40 ...150) details.
• VA-7200 electric actuators (DN 40)
Actuator Selection
Pneumatic actuator Direct Acting pneumatic actuators Reverse Acting pneumatic actuators
MP-822xxxx0 and PA-2xx0-3x1x MP-832xxxx0 and PA-2xx0-3x2x
Valve type Air pressure Spring-return Air pressure Spring-return
extends stem retracts stem retracts stem extends stem
E
2-way PDTC VG82..
Electric actuator Control mode Fail safe position (spring return only)
VA-72xx-820x, FA-25xx-751x FA-22xx-751x
RA-3xxx-7x2x, RA-3100-8x2x and FA-26xx-741x FA-23xx-741x
FA-2xxx-7x1x FA-27xx-711x FA-24xx-711x
Power failure Power failure
Actuator extends Actuator retracts
Valve type (spring force) (spring force)
stem stem
retracts stem extends stem
E
2-way PDTC VG82..
E = Equal percentage control characteristic = Flow
L = Linear control characteristic = No flow
E18.2
4 VG8300N & H
Pneumatic Actuator Selection MP8000 series
All actuators are reversible for Normally Closed or
Normally Open operation on the two-way PDTC MP8 2 20
(NO) valve body.
Options
The actuators can also be optionally equipped
with a factory fitted positioner and/or a hand 0 None
wheel. The positioner PY-1010 is direct acting 2 Feedback 2 kΩ and
and can be used with D.A. or R.A. actuators of the (2) Auxiliary switches
MP8000 and PA-2000 series.
Options
The actuators are available for valve sizes: (Positioner and hand wheel)
Valves DN 40 : MP8000 series 5 None
Valves DN 40 – 150 : PA-2000 series 6 Positioner D.A. PY-1010
Mounting kits for in-situ installation: hand 7 Positioner D.A. PY-1010
wheel, feedback assembly and auxiliary switches with hand wheel
are available on request. 8 Hand wheel
Ordering codes for Pneumatic Actuators Spring Range
PA-2000 series
C 20…50 kPa
PA-2 -3
E 60...90 kPa
Spring Range
Action, size
2 20…50kPa
7 70...100 kPa 2 D.A., 160 cm2
Action 3 R.A., 160 cm2
1 Direct Acting (D.A.)
2 Reverse Acting (R.A.)
Size
2 150 cm2 for
DN 15…DN 40
3 300 cm2, standard for
DN 50...DN 80
6 600 cm2, standard for
DN 100...DN 150
Options
0 None
3 Feedback 2kΩ and
(2) auxiliary switches
Positioner, factory fitted
0 None
3 DA type (PY-1010)
Hand wheel
0 None
1 With Hand wheel
The PA-2000 can be specially ordered as a
Teflon-free model, in conjunction with the
VG8300N and the VG8300H series. Please
contact your Johnson Controls distributor.
E18.2
VG8300N & H 5
Electric Actuator Selection RA-3000 Electric Actuators
Non Spring Return Actuators The RA-3000-7x2x series, synchronous motor-
driven actuator is available for 3-point (floating) or
VA-7200 Electric Actuators 0…10 VDC proportional control. It features factory
calibrated pressure switches to provide specified
The VA-7200 series synchronous motor-driven close-off ratings.
actuator is available for 3-point (floating) or for
0…10 VDC proportional control. It features a This actuator is available in three sizes: the
magnetic clutch coupling and provides a 1000 N RA-3000-712x with 1600 N thrust and
nominal thrust. It can be used in conjunction with approximately 82 sec running time for the 13 mm
VG8300N and VG8300H valve size DN 40. stroke DN 40 valves, the RA-3000-722x with 1800
N thrust and approximately 140 seconds running
Ordering codes for VA-7200 Electric Actuators
time for the 25 mm stroke DN 50…80 valves and
VA-72 -820 the RA-3000-732x with 3000 N thrust and
approximately 185 sec running time for the 42 mm
Supply voltage stroke DN 50…150 valves, in accordance with the
1 24 V 50/60 Hz max. close-off pressure ratings specified. Factory
fitted options, such as a 2kΩ feedback
3 230 V 50/60 Hz*
potentiometer, auxiliary switches and manual
Options override are also available.
3-point models Ordering codes for standard RA-Electric
Manual Actuators
Feedback Override
00* No No RA-3 -7
01 0…10 V (pot) No Thrust & Supply Voltage
03 2 kΩ No
126 1600 N 24 V, 50/60 Hz
20 (2) aux. switches No 127 1600 N 230 V,50/60 Hz
40* No Yes 226 1800 N 24 V, 50/60 Hz
41 0…10 V (pot) Yes 227 1800 N 230 V,50/60 Hz
43 2 kΩ Yes 325 3000 N 24 V, 60 Hz
50 (2) aux. switches Yes 326 3000 N 24 V, 50 Hz
70 (1) aux. switch Yes 327 3000 N 230 V, 50 Hz
(1) switch for manual 328 3000 N 230 V, 60 Hz
override signal
Options, factory mounted
Proportional models (0…10V) 00 None
Manual 03 (2) Aux. switches and
Feedback Override 2 kΩ feedback
02 No No potentiometer
06 0…10 V (pot) No 05 (2) Aux. switches and
22 (2) Aux. switches No 135 Ω feedback pot.
42 No Yes 41 Positioner 0...10 VDC
and (2) aux. switches
46 0…10 V (pot) Yes (Only 24 VAC models)
52 (2) Aux. switches Yes
Manual Operation
72 (1) Aux. switch Yes
0 None
(1) Switch for auto/manual
indication 1 With manual operation
(*) Only the VA-7200-8203 and VA-7240-8203
models are available with 230 VAC power
supply.
Note: All models with manual override and
24 VAC power supply are equipped with a
power cut-off switch.
E18.2
6 VG8300N & H
The RA-3100-8x2x series, synchronous motor- Spring Return Actuators
driven fast running actuator is available for 3-point
FA-2000 Electric Spring Return Actuators
(floating) or 0…10 VDC proportional control. It
features factory calibrated pressure switches to The FA-2000 series synchronous motor-driven
provide specified close-off ratings. S.R. actuators are available for 3-point (floating)
or with electronic positioner for
This actuator is available in two models: The
0…10 V / 0(4)…20 mA control. It provides a fully
RA-3100-8126 with 1200 N nominal thrust and
variable aperture, a power failure spring return
approximately 23.4 sec. running time for the
safety mechanism and an electrical manual-
13 mm stroke DN 40 valves and the
override (two spring-loaded push buttons).
RA-3100-8226 with 1700 N nominal thrust and
approximately 17.5 sec. running time for the On power failure, the actuator returns to normal
25 mm stroke DN 50…DN 80 valves and position.
approximately 29.4 sec. running time for the
For example on power failure:
42 mm stroke DN 100…DN 150 valves, in
accordance with the max. close-off pressure • The FA-2200, FA-2300 and FA-2400 models
ratings specified. Factory fitted options, such as a extend the stem, thus, when mounted on a
2kΩ feedback potentiometer auxiliary switches two-way PDTC valve, normal position closes
and manual override are also available. the valve.
• The FA-2500, FA-2600 and FA-2700 models
Ordering codes for fast running RA-Electric
retract the stem, thus, when mounted on a
Actuators
two-way PDTC valve, normal position opens
RA-31 -8 the valve.
Thrust & Supply Voltage Factory fitted auxiliary switches and 2kΩ-
126 1200 N 24 V, 50 Hz feedback potentiometer are order options.
This actuator series can be used in conjunction
226 1700 N 24 V,50/60 Hz
with DN 40...DN 150 VG8300N & VG8300H valve
Options, factory mounted bodies.
00 None
03 (2) Aux. switches and Electric Spring Return Actuator Ordering
2 kΩ feedback Codes for:
potentiometer FA-2xxx-711x with 13 mm stroke and 2000 N
41 Positioner 0...10 VDC thrust
and (2) aux. switches FA-2 - 7 11
(Only 24 VAC models)
Voltage supply type
1 230V, 50 Hz
6 24 V, 50 Hz
Factory fitted accessories
00 None
01 (2) Auxiliary switches
02 2 kΩ feedback pot.
03 (2) Auxiliary switches and
2 kΩ feedback pot.
04 135 Ω feedback pot.
40 Built-in electronic positioner
0…10 V / 0…20 mA *
41 Built-in electronic positioner
0…10 V / 0…20 mA and
(2) Auxiliary switches
Spring return function
4 Pre-set position: stem fully
extended, DN 40
7 Pre-set direction: stem fully
retracts, DN 40
* Not for 230 V model
E18.2
VG8300N & H 7
FA-2xxx-751x electric spring return actuators FA-2xxx-741x electric spring return actuators
with 25 mm stroke and 2400 N thrust with 42 mm stroke and 2200N thrust
FA-2 -7 5 1 FA-2 -7 4 1
Voltage supply type Voltage supply type
1 230V, 50 Hz 1 230V, 50 Hz
6 24 V, 50 Hz 6 24 V, 50 Hz
Factory fitted accessories Factory fitted accessories
00 None 00 None
01 (2) Auxiliary switches 01 (2) Auxiliary switches
02 2 kΩ feedback pot. 02 2 kΩ feedback pot.
03 (2) Auxiliary switches and 03 (2) Auxiliary switches and
2 kΩ feedback pot. 2 kΩ feedback pot.
04 135 Ω feedback pot. 04 135 Ω feedback pot.
40 Built-in electronic positioner 40 Built-in electronic positioner
0…10 V / 0…20 mA * 0…10 V / 0…20 mA *
41 Built-in electronic positioner 41 Built-in electronic positioner
0…10 V / 0…20 mA and 0…10 V / 0…20 mA and
(2) Auxiliary switches (2) Auxiliary switches
Spring return function Spring return function
2 Pre-set direction: stem fully 3 Pre-set direction: stem fully
extends, DN 50…80 extends, DN 100…150
5 Pre-set direction: stem fully 6 Pre-set direction: stem fully
retracts, DN 50…80 retracts, DN 100…150
* Not for 230 V model * Not for 230 V model
Ordering Procedure
The two-way PDTC valves and actuators can be ordered separately or as a factory fitted combinations.
When factory mounted, please add “+M” behind the order code for the actuator.
For example:
For a DN 65, kvs 63, PN16 valve plus actuator with electric positioner 0...10 V input, 24 VAC
50 Hz supply, order:
Item 1 VG83G1S1N (valve body)
Item 2 RA-3041-7326 (actuator)
Alternatively if order is for factory mounted option:
Item 1 VG83G1S1N (valve body)
Item 2 RA-3041-7326 +M (actuator)
E18.2
8 VG8300N & H
C lose-off pressures
Maximum Close-off Pressures for Pneumatic Valve-Actuators with VG8300 Valves (kPa)
2-way PDTC with
2-way PDTC with
Direct Acting actuator
Actuator model Reverse Acting actuator
(actuator supply air pressure
(spring-return closes valve)
closes valve)
0 kPa 120…160 kPa
Stroke Diaph. area DN kvs
Spring range Spring range
(mm) (cm²) [kPa] [kPa]
70 - 100; (60-90)* 20 - 50
Spring ID No. Spring ID No.
63 23
MP8000
13 160 40 16, 25
PA-2000-3200
13 150 40 16, 25
PA-2000-3300 50 40 PN 16 = 1600
65 63 PN 25 = 2500
25 300
80 100
PA-2000-3600 100 160
125 250
42 600
150 350
* (For MP8000)
Maximum Close-off Pressures for Electric Valve-Actuators with VG8300N PN 16 Valves (kPa)
Actuator Stroke Thrust Body Size DN
(mm) (N) 40 50 65 80 100 125 150
Non Spring Return Actuators
VA-7200 13 1000 - - - - - -
1600
RA-3000-712x 13 1600 - - - - - -
RA-3000-722x 25 1800 - - - -
1600
RA-3000-732x 42 3000 - 1600
Spring Return Actuators
FA-2000-711x 13 2000 1600 - - - - - -
FA-2000-751x 25 2400 - 1600 - - -
FA-2000-741x 42 2200 - - - - 1600
Non-Spring Return Actuators
RA-3100-8126 13 1200 1600 - - - - - -
RA-3100-8226 25 & 42 1700 - 1600
Maximum Close-off Pressures for Electric Valve-Actuators with VG8300H PN 25 Valves (kPa)
Actuator Stroke Thrust Body Size DN
(mm) (N) 40 50 65 80 100 125 150
Non Spring Return Actuators
VA-7200 13 1000 - - - - - -
2500
RA-3000-712x 13 1600 - - - - - -
RA-3000-722x 25 1800 2500 - - -
RA-3000-732x 42 3000 2500
Spring Return Actuators
FA-2000-711x 13 2000 2500 - - - - - -
FA-2000-751x 25 2400 2500 - - -
FA-2000-741x 42 2200 - - - 2500
Non-Spring Return Actuators
RA-3100-8126 13 1200 2500 - - - - - -
RA-3100-8226 25 & 42 1700 - 2500
E18.2
VG8300N & H 9
I nstallation and Servicing
When mounting the VG8300N and VG8300H When servicing the VG8300N and VG8300H
series valves please follow the instructions below: series valves, make sure that:
• It is recommended that the valves be mounted • The pneumatic or electrical power to the
at angles not greater than 90° from the upright actuator is isolated.
position, in a conveniently accessible location.
• You do not touch or attempt to connect or
• Do not cover the actuator with insulating disconnect wires when electrical power is on.
material.
• Sufficient clearance must be allowed for
WARNING
actuator removal (refer to the dimension
drawings on pages 11, 13, 14, 15 and 16) Shock Hazard
• Install the valve as indicated by the arrow(s) on Disconnect the power supply before wiring
the valve body so that the plug seats against connections are made to prevent personal injury.
the flow. Equipment Damage Hazard
• Johnson Controls must approve use of the Make and check all wiring connections before
VG8300N and VG8300H series valves with applying power to the system. Short circuited or
fluids other than specified. improperly connected wires may result in
• On electrically actuated valve assemblies, all permanent damage to the unit.
wiring must be in accordance with applicable
electrical codes and ordinances. • No air pressure is applied to the piping system
when servicing the valve.
• Input lines to the actuator must be wired
correctly to open or close the valve as is • No attempt is made to remove the spring of a
functionally required. pneumatic actuator from its housing.
Ordering Code for Replacement Packing Kits
Ordering For valves Installation
Code kit ordering
code
Standard packing kit:
121 4393 011 DN 40 -
121 4409 011 DN 50...80 -
121 4433 011 DN 100...150 -
* Glycerine cup packing kit:
121 4434 011 DN 40 121 4434 111
121 4435 011 DN 50...80 121 4435 111
121 4436 011 DN 100...150 121 4436 111
* Installation kit required
E18.2
10 VG8300N & H
D imensions ( in mm): Pneumatic Actuators and VG8300 valves, DN 40…DN 150
MP8000 with Hand-Wheel PA-2000 with Hand-Wheel
A
A
Without Without
Hand-Wheel Hand-Wheel
H11 Only on:
PA-2000-3200 &
H12 PA-2000-3300
D Approx.
27.5
H11 H12
H2
H6
Positioner D
H2 H6
d
H5
B
DN
D3
D2
D1
Valve and Actuator dimensions VG8300 PN 16 and PN 25 Valves
Valve body MP8200 & MP8300 PA-2000-3200
DN B H5 A A *) D H2 H6 H11 H12 A D H2 H6 H11 H12
40 200 78 160 220 219 345 495 551 600 220 205 375 525 463 613
*) For actuator with positioner
Valve body PA-2000-3300 PA-2000-3600 & PA-2000-3700
DN B H5 A D H2 H6 H11 H12 A D H2 H6 H11 H12
50 230 101 235 290 479 629 593 743 250 384 609 809 767 967
65 290 102 235 290 480 630 594 744 250 384 610 810 768 968
80 310 108 235 290 486 636 600 750 250 384 616 816 774 974
100 350 136 - - - - - - 250 384 644 844 802 1002
125 400 155 - - - - - - 250 384 663 863 821 1021
150 480 175 - - - - - - 250 384 683 883 841 1041
Flange Dimensions
DN D1 D2 D3 d Bolts Holes DN D1 D2 D3 d d Bolts Holes
PN 16 PN 16 PN 25 PN 16 PN 25
40 150 110 88 17.5 M16 x 55 4 100 220 180 158 17.5 M16 x 70 22 M20 x 70 8
50 165 125 102 17.5 M16 x 60 4 125 250 210 188 17.5 M16 x 75 26 M20 x 75 8
65 185 145 122 17.5 M16 x 60 4 8 150 285 240 212 22 M20 x 60 26 M20 x 80 8
80 200 160 138 17.5 M16 x 65 8
*) For actuator with positioner
E18.2
VG8300N & H 11
D imensions (in mm): VA-7200 & RA-3000 electric actuators for VG8300 valves (DN 40)
VA-7200 RA-3000
A A
∅ 106
N 186 x 166
H6
H6
H11
H2
H2
d
H5
H5
DN B
D3
D2
D1
B
Flange Dimensions
DN D1 D2 D3 d Bolts Holes
40 150 110 88 17.5 M16 x 55 4
Valve and Actuator dimensions
Valve body VA-7200 RA-3000
DN B H5 A H2 H11 H6 A H2 H6
40 200 78 160 291 318 470 160 386 550
E18.2
12 VG8300N & H
D imensions (in mm):FA-2000 Electric Actuator for VG8300 Valves, (DN 40)
FA-2000-7110
A
162 x 162
H6
H2
∅ 147
d
H5
DN
D3 B
D2
D1
Flange Dimensions
DN D1 D2 D3 d Bolts Holes
40 150 110 88 17.5 M16 x 55 4
Valve and Actuator dimensions
Valve body FA-2000
DN B H5 A H2*) H6*)
40 200 78 160 590 830
*) For models with
positioner add 40 mm
E18.2
VG8300N & H 13
D imensions (in mm): FA-2000 Electric Actuator for VG8300 Valves (DN 50 - 150)
FA-2000-7510 & -7410
A
162 x 162
∅ 147 H6
H2
d
H5
DN
D3 B
D2
D1
Flange Dimensions
DN D1 D2 D3 d Bolts d Bolts Holes
PN 16 PN 25 PN 16 PN 25
50 165 125 102 17.5 M16 x 60 17.5 M16 x 60 4 4
65 185 145 122 17.5 M16 x 60 17.5 M16 x 60 4 8
80 200 160 138 17.5 M16 x 65 17.5 M16 x 65 8 8
100 220 180 158 17.5 M16 x 70 22 M20 x 70 8 8
125 250 210 188 17.5 M16 x 75 26 M20 x 75 8 8
150 285 240 212 22 M20 x 60 26 M20 x 80 8 8
Valve and Actuator dimensions
Valve body FA-2000
DN B H5 A H2 *) H6 *)
50 230 101 160 642 880
65 290 102 160 643 880
80 310 108 160 649 880
100 350 136 160 711 950
125 400 155 160 730 970
150 480 175 160 750 990
*) Add 40 mm for models with positioner
E18.2
14 VG8300N & H
D imensions (in mm): Electric Actuators RA-3000 for VG8300 valves (DN 50 - 150)
A
186 x 166
H6
H2
d
H5
DN B
D3
D2
D1
Flange Dimensions
DN D1 D2 D3 d Bolts d Bolts Holes
PN 16 PN 25 PN 16 PN 25
50 165 125 102 17.5 M16 x 60 17.5 M16 x 60 4 4
65 185 145 122 17.5 M16 x 60 17.5 M16 x 60 4 8
80 200 160 138 17.5 M16 x 65 17.5 M16 x 65 8 8
100 220 180 158 17.5 M16 x 70 22 M20 x 70 8 8
125 250 210 188 17.5 M16 x 75 26 M20 x 75 8 8
150 285 240 212 22 M20 x 60 26 M20 x 80 8 8
Valve and Actuator dimensions
Valve body RA-3000
DN B H5 A H2 H6
50 230 101 160 408 580
65 290 102 160 409 580
80 310 108 160 415 580
100 350 136 160 443 600
125 400 155 160 462 630
150 480 175 160 482 640
**) Add 15 mm for models with positioner
E18.2
VG8300N & H 15
S pecifications
Product: VG8300N, PN 16 flanged valves VG8300H PN 25 flanged valves
Models: 2-way Balanced pressure (PDTC) DN 40…150 2-way Balanced pressure (PDTC) DN 40…150
Service: Water, glycol solutions (max 50%) or steam for HVAC applications
(Proper water treatment is recommended, refer to VDI 2035)
Valve body data: DN: 40 50 65 80 100 125 150
kvs: 25 40 63 100 160 250 350
Weight (kg) VG8300N: 12 14 18.5 25.5 35.5 55 75
Nominal stroke in mm: 13 25 42
kPa
PN 25
2500
2100
2000
Pressure / Temperature 1600 PN 16
1500
characteristics: -10 °C
1300
1000
500
0
-20 0 20 40 60 80 100 120 140 160 180 200 °C
2°C... 180 °C (with DN 125 & DN 150
2°C...200 °C; -20 °C when optional glycerine
Fluid temperature limits: 2°C…130°C); -10 °C when optional glycerine cup is used (below 0°C optional glycerine cup
cup is used (below 0°C optional glycerine cup
must be used).
must be used).
Material Nodular cast iron EN-GJS-400-15, Mat. spec.
Nodular cast iron In accordance with EN-GJS-
Body: No. EN-JS1030
400-18-LT, Mat.spec. No. EN-JS1025
Stem / Plug / Seat edge: Stainless steel, Material specification 1.4305
Teflon-Viton-Teflon V-ring combination, spring loaded, self adjusting
Packing:
(Aramid fibre-Viton- Aramid fibre when glycerine cup is used)
Face to face dimensions: In accordance with DIN EN558-1
Flange dimensions: DIN EN1092-2, form B seal strip
(Pre-welded flange, recommended in accordance with DIN EN1092-2)
Flow characteristics
Characteristic: Equal percentage
Practical rangeability (kvs / kvr): 100:1
Sensitivity ngl(ideal 4.5 for kvs ≥ 1; 3.2 for kvs 0.4…0.63
rangeability):
500 kPa with water. 1000 kPa with water.
Max. ∆pv100: 800 kPa with heavy duty model for 1600 kPa with heavy duty model for
super heated steam super heated steam
Leakage rate: Max. 0.05 % of kvs DIN 32730; Test with water as per DIN EN1349
Type of device: Pressure accessory conforms to the 97/23/EU as per module D1 for DN 40…DN 125
Pressure accessory conforms to the 97/23/EU as per modules B & D for DN 150
Notified body: TÜV Süddeutschland Bau & Betrieb GmbH; ID No. 0036
Standards and specifications: DIN EN60534-1, DIN EN558-1, DIN EN1092-2 and DIN EN 1349
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. are not liable for damages resulting from misapplication or
misuse of its products.
Johnson Controls International, Inc.
Headquarters: Milwaukee, Wisconsin, USA
European Customer Service Center: Westendhof 3, D-45143 Essen, Germany
European Factories: Essen (Germany), Leeuwarden (The Netherlands) and Lomagna (Italy)
Branch Offices Principal European Cities. : Printed in Germany
E18.2
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.