Файл за старою адресою не зберігся. Нижче — документ виробника на те саме обладнання.
| Вид документа | Технічний паспорт |
|---|---|
| Виробник | JCI |
| Моделі | TM-1140-0000, TM-1150-0000, TM-1160-0000, TM-1160-0005, TM-1160-0002, TM-1160-0007, TM-1170-0005, TM-1170-0007 |
| Група обладнання | automation |
| Мова документа | англійська |
| Розмір файлу | 0.3 МБ |
Про документ
The TM-1100 series of Room Command Modules are designed for use with the TC-9102, TC-9109 and TCU series of DDC terminal unit controllers. The set point dial enables the room occupant to adjust the working set point within the range of 12…28 °C or -3 K to +3 K, according to the model number. The occupancy button switches the controller between COMFORT and STANDBY or requests a temporary COMFORT mode during NIGHT operation; a LED indicator shows the current operating mode.
Ключові дані
| set point dial range | 12…28 °C or ± (-3 K to +3 K) |
|---|---|
| ambient operating conditions | 0 to 50 °C, 10 to 90% RH non condensing |
| temperature sensor | NTC Thermistor 0 to 40°C, 2252 ohm at 25 °C |
| sensor accuracy | +/-0.5 °C |
| remote set point | 10 kOhm potentiometer marked for 12 °C to 28 °C or (range 3 K) |
| mode indicator | Green LED (5V, 4 mA) |
| protection class | IP30 (EN 60529) |
| dimensions | 80 mm x 80 mm x 32 mm / 80 mm x 80 mm x 35 mm |
Застосування
- Wall-mounted room unit for rooms controlled by TC-9102/TC-9109 and TCU series DDC terminal unit controllers
- Fan coil applications with TC-9102 and TCU Fan Coil Unit controllers via 3-speed fan override models
- Models without temperature sensor where the room temperature sensor is mounted inside the Fan Coil Unit
- Public buildings and hotels
Особливості
- Modern and attractive cover which snaps onto a plug-in mounting base — blends in with room decor, easy installation
- Terminals located on mounting base — easy wiring and commissioning
- All models available with or without occupancy override button
- Set point dial marked 12…28 °C or ± (deviation to programmed room temperature set point)
- 3-speed fan override adjuster (Auto, Off, I, II, III) with TC-9102; only active in COMFORT mode, fan always at high speed in Low Limit mode
- LED mode indicator: steady on = COMFORT, flashing = STANDBY, off = NIGHT/OFF
Технічні дані
| Parameter | Value |
|---|---|
| Supply Voltage | Power from TC-9102, TC-9109 or TCU Series Controller |
| Ambient Operating Conditions | 0 to 50 °C, 10 to 90% RH non condensing |
| Ambient Storage Conditions | -20 to 70 °C, 10 to 90% RH non condensing |
| Terminations | Terminal block in base for 1 x 1.5 mm² (maximum) cable |
| Temperature Sensor | NTC Thermistor 0 to 40°C, 2252 ohm at 25 °C |
| Accuracy | +/-0.5 °C |
| Remote Set Point | 10 kOhm potentiometer marked for 12 °C to 28 °C or (range 3 K) |
| 3-Speed Fan Override | 10 kOhm potentiometer with mechanically guided positions for Auto, Off, I (low speed), II (medium speed) and III (high speed) |
| Occupancy Button | Momentary contact (switches 5V at 1 mA) |
| Mode Indicator | Green LED (5V, 4 mA) |
| Wiring distance | Max 50 m (min. 0.8 mm diameter wire) |
| Mounting | Direct surface mount, plastic base for surface mount with wiring conduits |
| Materials | ABS+PC; self extinguishing HB UL 94 |
| Colours | RAL9016 (GE86280), RAL7047 (GE GY81118) |
| Protection Class Enclosure | IP30 (EN 60529) |
| Dimensions (H x W x S), TM-1140-0000 | 80 mm x 80 mm x 32 mm |
| Dimensions (H x W x S), TM-1150/TM-1160/TM-1170/TM-1190 | 80 mm x 80 mm x 35 mm |
| Shipping Weight | 0.15 kg |
Варіанти замовлення
Table: Room Command Module
| Ordering Code | Occupancy Button | Temperature Setpoint Dial Scale | Fan Speed Override | Built-in Sensor |
|---|---|---|---|---|
| TM-1140-0000 | - | - | - | NTC K2 |
| TM-1150-0000 | Yes | - | - | NTC K2 |
| TM-1160-0000 | Yes | 12...28 °C | - | NTC K2 |
| TM-1160-0005 | Yes | ± | - | NTC K2 |
| TM-1160-0002 | Yes | 12...28 °C | 3-speed fan override | NTC K2 |
| TM-1160-0007 | Yes | ± | 3-speed fan override | NTC K2 |
| TM-1170-0005 | Yes | ± | - | - |
| TM-1170-0007 | Yes | ± | 3-speed fan override | - |
| TM-1190-0000 | - | 12...28 °C | - | NTC K2 |
| TM-1190-0005 | - | ± | - | NTC K2 |
Accessories:
- TM-1100-8931 Plastic Surface Mounting Base - White
- TE-9100-8501 Unit Mount NTC Temperature Sensor (1.5-m cable)
- TM-9100-8900 Special tool for opening enclosure
Допуски та стандарти
- EMC Directive 2004/108/EC compliance declared by Johnson Controls, Inc.
- IP30 per EN 60529
- UL 94 HB self-extinguishing enclosure material
Позиції каталогу з цим документом
Текст документа
Product Bulletin TM-1100
Issue Date 02 2011
TM-1100 Series Room Command Module
The TM-1100 series of Room Command Modules are
designed for use with the TC-9102, TC-9109 and TCU
series of DDC terminal unit controllers. The set point
dial enables the room occupant to adjust the working
set point of the controller within the range of 12…28 °C
or -3 K to +3 K, according to the model number.
The occupancy button enables the occupant to switch
the mode of operation of the controller between
COMFORT and STANDBY or to request a temporary TM-1140-0000 TM-1150-0000
COMFORT mode during NIGHT operation.
A LED indicator shows the current operating mode.
For TC-9102 and TCU Fan Coil Unit controllers,
a Room Command Module with a 3-speed fan
override adjuster is available, and models without a
temperature sensor are provided for application where
the room temperature sensor is mounted inside the
Fan Coil Unit. TM-1190-0005 TM-1160-0000 TM-1160-0007
Features and Benefits
Modern and attractive cover which snaps Blends in with room decor.
onto a plug-in mounting base Easy installation.
Terminals located on mounting base. Easy wiring and commissioning.
All models available with or without Covers a large number of applications in public
Occupancy override button buildings and hotels
© 2011 Johnson Controls, Inc. 1
Code N. 24.140 E www.johnsoncontrols.com
Application Overview
Set Point Dial Mode Indicator
The Room Command Module is available with a set The LED indicator directly next to the Occupancy
point dial marked 12…28 °C or ±. The module must Button shows the current operating mode of the
be connected to a TC-9102/9 TCU series controller controller as follows:
with the corresponding remote set point range. Steady On COMFORT Mode (occupied)
The 12…28 °C range module determines the set Flashing STANDBY Mode
point of the controller while the ± range module
gives a deviation to the room temperature set point Off NIGHT (unoccupied) or OFF Mode
programmed into the controller.
3-Speed Fan Override Adjuster
Refer to “Ordering Codes”.
When connected to a TC-9102 Controller which has
Occupancy Button a 3-speed fan control auxiliary output, the 3-speed
fan override adjuster allows manual control of the
When pressed for approximately one second, speed of the fan. The positions of the adjuster are
the occupancy button changes the mode of as follows:
operation of the controller to the “alternate” mode or
back to normal mode. When the controller is in AUTO Automatic fan speed is set by the TC-9102
COMFORT (occupied) mode the alternate mode is or TCU Controller.
STANDBY (and vice versa), and when in NIGHT OFF Fan OFF
(unoccupied) mode the alternate mode is a
temporary COMFORT (bypass) mode for a period of I Fan low speed
one hour. II Fan medium speed
Full details of the alternate modes can be found in
the “TC-9102 Technical Bulletin” (Ordering Code III Fan high speed
MN-9100-2117) of the System 91 Manual or “TCU The fan speed adjuster is only active when the
Technical Bulletin” (Ordering Code MN-LCC-01) in controller is in COMFORT mode. In Low Limit mode
LONWORKS® Compatible Controllers Manual. the fan always runs at high speed.
Ordering Codes
Table 1: Room Command Module
Occupancy Temperature Setpoint
Ordering Codes Fan Speed Override Built-in Sensor
Button Dial Scale
TM-1140-0000 - - - NTC K2
TM-1150-0000 - Yes - NTC K2
TM-1160-0000 - Yes 12...28 °C NTC K2
TM-1160-0005 - Yes ± NTC K2
TM-1160-0002 3-speed fan override Yes 12...28 °C NTC K2
TM-1160-0007 ±
3-speed fan override Yes NTC K2
TM-1170-0005 ±
- Yes -
TM-1170-0007 ±
3-speed fan override Yes -
TM-1190-0000 - - 12...28 °C NTC K2
TM-1190-0005 - - ± NTC K2
Table 2: Accessories
Ordering Codes Description
TM-1100-8931 Plastic Surface Mounting Base - White
TE-9100-8501 Unit Mount NTC Temperature Sensor (1.5-m cable)
TM-9100-8900 Special tool for opening enclosure
2 TM-1100 Series Room Command Module
Installation Mounting
The TM-1100 Series Room Command Module is Remove the base of the module from the cover by
designed for wall mounting in the room to be inserting the point of the special TM tool (Ordering
controlled. It should be located where the occupant Code TM-9100-8900) into the small hole at the
can easily read and adjust the set point and fan center top of the cover. While pressing down gently,
speed override. If the module has an NTC prise the base away from the cover. As the two parts
temperature sensor, it should be placed where the separate, remove the tool and continue to pull the
temperature is representative of the general room cover away from the base until the cover is free.
conditions. Cold or warm air draughts, radiant heat To reassemble the room command module, place
and direct sunlight should be avoided. the cover over the lower edge of the base and push
the upper part of the cover until it “clicks” firmly in
The installation of electrical wiring must conform to
place.
local codes and should be carried out by authorized
personnel only. Users should ensure that all
Johnson Controls products are used safely and
without risk to health or property.
TM-9100-8900
Figure 1: Removing Cover from Base
TM-1100 Series Room Command Module 3
Direct Surface Mounting Surface Mounting with Mounting Kit
For direct surface mounting: (TM-1100-8931)
U P OB EN
A
B
1. Remove one of the notches (A) with a suitable
tool.
2. Mark the position of the holes (B) on the wall and
drill holes 5 mm in diameter. Insert plastic plugs
into holes.
D
C
Figure 2: Module Base (Dimensions in mm)
1. Mount the module base on the wall to cover the
electrical outlet and secure with at least two screws.
Conduit
3. Position and fix the mounting base to the wall
using the two long screws (C) provided in the kit.
4. Fix the base of the TM-1100 to the mounting
base using the two short screws (D) provided in
the kit.
U P OB EN
58
5.0 78
3.5
25 78
11
17
13
20
Figure 3: Surface Mounting Base
(Dimensions in mm)
4 TM-1100 Series Room Command Module
Wiring
wires. Follow the wiring diagrams shown in the
Before connecting or disconnecting any wires,
figures below. All wiring to the module is at extra low
ensure that all power supplies have been switched
(safe) voltage and must be separated from power
off and all wires are potential-free to prevent
line voltage wiring. Do not run wiring close to
equipment damage and avoid electrical shock.
transformers or high frequency generating
Terminations are made on the terminal blocks in the
equipment. Complete and verify all wiring
base of the module, which accept up to 1.5 mm2
connections before applying power to the controller
to which the module is connected.
AD-TCU
TC-9102/9 Series TM-110 Series
Controllers Room Command Module
20 20 NTC Sensor
21 21 Common
Max 50 m
(Min. 0.8 mm diameter wire)
Figure 4: TM-1140-0000 Wiring
AD-TCU
TC-9102/9 Series TM-110 Series
Controllers Room Command Module
14 14 Occupancy Button
15 15 Mode LED
20 20 NTC Sensor
21 21 Common
Max 50 m
(Min. 0.8 mm diameter wire)
Figure 5: TM-1150-0000 Wiring
TM-1100 Series Room Command Module 5
AD-TCU
TC-9102/9 Series TM-110 Series
Controllers Room Command Module
14 14 Occupancy Button
15 15 Mode LED
20 20 NTC Sensor
23 23 Remote Set Point
21 21 Common
22 22 +5V
Max 50 m
(Min. 0.8 mm diameter wire)
Figure 6: TM-1160-0000 and TM-1160-0005 Wirings
AD-TCU
TC-9102/9 Series TM-110 Series
Controllers Room Command Module
51 51
Three-Speed Fan
Override
14 14 Occupancy Button
15 15 Mode LED
20 20 NTC Sensor
23 23 Remote Set Point
21 21 Common
22 22 +5V
Max 50 m
(Min. 0.8 mm diameter wire)
Figure 7: TM-1160-0002 and TM-1160-0007 Wirings
6 TM-1100 Series Room Command Module
AD-TCU
TC-9102/9 Series TM-110 Series
Controllers Room Command Module
14 14 Occupancy Button
15 15 Mode LED
23 23 Remote Set Point
21 21 Common
22 22 +5V
Max 50 m
(Min. 0.8 mm diameter wire)
Figure 8: TM-1170-0005 Wiring
AD-TCU
TC-9102/9 Series TM-110 Series
Controllers Room Command Module
51 51
Three-Speed Fan
Override
14 14 Occupancy Button
15 15 Mode LED
23 23 Remote Set Point
21 21 Common
22 22 +5V
Max 50 m
(Min. 0.8 mm diameter wire)
Figure 9: TM-1170-0007 Wiring
TM-1100 Series Room Command Module 7
AD-TCU
TC-9102/9 Series TM-110 Series
Controllers Room Command Module
20 20 NTC Sensor
23 23 Remote Set Point
21 21 Common
22 22 +5V
Max 50 m
(Min. 0.8 mm diameter wire)
Figure 10: TM-1190-0000 and TM-1190-0005 Wirings
8 TM-1100 Series Room Command Module
Dimensions
Figure 11: TM-1140-0000
Mode
LED
Occupancy
Button
Figure 12: TM-1150-0000
Temperature
Set Point
Adjustment
Dial
Figure 13: TM-1190-0005
TM-1100 Series Room Command Module 9
Three Fan
Speed
Override
Figure 14: TM-1160-0007 and TM-1170-0007
Figure 15: TM-1160-0000
Figure 16: TM-1190-0000
10 TM-1100 Series Room Command Module
Technical Specifications
Supply Voltage Power from TC-9102, TC-9109 or TCU Series Controller
Ambient Operating 0 to 50 °C
Conditions 10 to 90% RH non condensing
Ambient Storage Conditions -20 to 70 °C
10 to 90% RH non condensing
Terminations Terminal block in base for 1 x 1.5 mm² (maximum) cable.
Temperature Sensor NTC Thermistor 0 to 40°C, 2252 ohm at 25 °C.
Accuracy +/-0.5 °C
Remote Set Point 10 kOhm potentiometer marked for 12 °C to 28 °C or (range 3 K )
3-Speed Fan Override 10 kOhm potentiometer with mechanically guided positions for
Auto, Off, I (low speed), II (medium speed) and III (high speed).
Occupancy Button Momentary contact (switches 5V at 1 mA).
Mode Indicator Green LED (5V, 4 mA)
Mounting Direct surface mount, plastic base for surface mount with wiring conduits
(See “Ordering Codes”)
Materials Enclosure
Base
Occupancy Override Button ABS+PC; self extinguishing HB UL 94
Fan Speed Override Dial
Setpoint Dial
Colours Enclosure
Base
RAL9016 (GE86280 )
Occupancy Override Button
Fan Speed Override Dial
Setpoint Dial RAL7047 (GE GY81118)
Protection Class Enclosure IP30 (EN 60529)
Dimensions (H x W xS) TM-1140-0000
80 mm x 80 mm x 32 mm
TM-1150-0000
TM-1160-000x
TM-1170-000x 80 mm x 80 mm x 35 mm
TM-1190-000x
Shipping Weight 0.15 kg
Compliance Johnson Controls, Inc. declares that these products are in compliance
with the essential requirements and other relevant provisions of the EMC
Directive 2004/108/EC
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications, consult
the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products.
Building Efficency
Headquarters: Milwaukee, Wisconsin, USA
Brach Offices: Principal Cities World-Wide
® ®
Metasys and Johnson Controls are registered trademarks of Johnson Controls, Inc.
All marks herein are the marks of their respective owners.
© Copyright 2011 Johnson Controls, Inc.All right reserved. All rights reserved.
Any unauthorized use or copying is strictly prohibited.
www.johnsoncontrols.com
TM-1100 Series Room Command Module 11
Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.