D-9502-5 Positioner Kit (For D-3244 and D-3246 Series Actuators) Installation Guide

Вид документа	Інструкція з монтажу
Виробник	JCI
Код документа	d-9502-5-positioner-kit-for-d-3244-and-d-3246-series-actuators-installation
Група обладнання	D-9502-5 Positioner Kit
Сторінок	4
Мова документа	англійська
Розмір файлу	1.2 МБ

Текст документа

-a+1621
CONTR~Ls@·
D-9502-5 Positioner Kit
(For D-3244 & D-3246 Series Actuators)

Kit Includes
1. 1 Posi tioner w;tover 5. 2 Self-Tapping Holding Screws
2. 1 Positioner Mounting Plate 6. 1 Positioner Spring (For D-3244)
3. 1 Pull Arm (For 0-3244) 7. 1 Installation Instructions
4. 2 t8-32 Screws

Note: To install a D-9502-5 positioner on a D-3246 series actuator, a new
positioner spring (D-265-603) and pull arm (D-9502-100) are required and must be
ordered separately.

Specifications

Maxil1lll11 Pressure 25 PSIG (175 kPa)

Starting Point Adjustable Fran 2 to 12 PSIG (14 to 84 kPa)

q,erating Span Adjustable Fran 3 to 13 PSI (21 to 91 kPa)

1/4 or 5/32 in. 1000 SCIH (273 1114's)
Qltput Barbed Fitting
capacity 1/4 in. Barbed
Fitti ng 1600 SCIM (437 J1141s)

Air connections Barbed Fittings for 5/32 or 1/4 in. o.o. Polytubing

Air Consunption 5 SCIM (1.4 J1141s)

Arilient q,erating -20 to 1500F (-29 to 66oC)
Tenflerature Limits

Repair Parts
(Order Separately)

The performance specifications are nominal and conform to acceptable Industry standards. For
appllcatlon at conditions beyond these specifications, consult the local Johnson Controls office. Johnson
Controls, Inc. shall not be //able for damages resulting from mlsappllcatlon or misuse of its products.

(0316)
II I llll I II III II lllllllllllll 111111111111111111111111111111
24-4891-3
24- 4891- 3, Rev . A
Rev. $ 1
PILOT "p"
OUTPUT "o"~

POSITIONER
STARTING POINT POSITIONER
ADJUSTING SCREW - - - ARM
ACTUATOR
AIR CONNECTION

FOR 0-3246 USE
D-9502-100
ARM

FOR D-3246 USE
LOCKNUT 0·265-603
SPRING
CONNECTION HEAD

Pig. l

Mounting Procedure !See Pig. ll
l. Secure the positioner mounting plate to the actuator with the two
self-tapping holding screws.
2. Remove the cover fran the positioner.
J, Secure the positioner to the llDWlting plate with the two 18-32
screws.
4. Ren>ve the connection head fran the actuator.
5. Slide the washer onto the rod up to the locknut.
6. Screw the connection head onto the rod up to the washer.
7. Slide the pull arm into the slot in the connection head.

2
8. Secure the assent>ly by tightening the locknut in place.

9. Attach one end of the spring to the pull arm and the other end to
the positioner arm. Note: If there is slack in the spring,
disconnect the spring from the pull arm, loosen the locknut, and
rotate the connection head and pull arm away fran the actuator to
a position where the spring would be just ~ut. Tighten the
locknut in place and recomect the spring to the pull arm.

Adjustments
The holes in the positioner arm determine the operating apan. The
hole nearest the fixed end represents an operating apan of l PSI
(21 kPa) and the hole furthest fran the fixed end represents an
operating span of 13 PSI (91 kPa) •
The starting point adjustment is the brass screw located on the
positioner (under the cover). Note: The other three acr- on the
positioner are factory settings and should not be adjusted. When
adjusting the positioner starting point, keep in mind that the sift
of the starting pressure and the span muat not exceed the supply
pressure. If the SID exceeds the supply pressure, the actuator will
not move over its full stroke.

Operational Checkout
To check the operation of the positioner, proceed as follows:
l. Apply 20 PSIG (140 kPa) to the BUR>lY •s• port.
2. Apply variable air (0 to 20 PSIG) to the pilot •p• port.
J, Connect the output •o• port of the positioner to the actuator
comec:tion.
4. Vary the pressure to the pilot •p• port. The actuator should
begin to stroke when the pilot pressure reaches the starting
point. The actuator should be fully stroked when the pilot
pressure reaches the high end of the operating span.

l
European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact:
JOHNSON CONTROLS JOHNSON CONTROLS JOHNSON CONTROLS
WESTENDHOF 3 507 E MICHIGAN ST C/O CONTROLS PRODUCT MANAGEMENT
45143 ESSEN MILWAUKEE WI 53202 NO. 22 BLOCK D NEW DISTRICT
GERMANY USA WUXI JIANGSU PROVINCE 214142
CHINA

Позиції каталогу з цим документом

Документ виробника, опублікований як довідковий матеріал на обладнання, яке ми постачаємо. Правовласник може попросити прибрати його — приберемо.